Bittel 48 Series Panduan Pengguna - Halaman 7
Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Telepon Bittel 48 Series. Bittel 48 Series 9 halaman.
Halaman Cetak
11.4 Receiving a second call (Two Line models only)
11.4.1 Press [HOLD] key, the current call will be on hold.
11.4.2 Press the appropriate [LINE] key for the new incoming call.
11.4.3 After completing the new call, press the [LINE] key of the
call on hold to resume the call.
12
12
12
12
ADJUSTING
ADJUSTING
ADJUSTING
ADJUSTING
HANDSET
HANDSET
HANDSET
HANDSET
VOLUME
VOLUME
VOLUME
VOLUME
During calling mode, press [VOL] key to adjust the volume for
handset and speaker. With each press, it cycled as Low –medium
–high, total three level.
After on-hook, the handset volume resume to the low level;
Speaker volume keep the current level.
13
ADJUSTING RING VOLUME
13
13
13 ADJUSTING RING VOLUME
ADJUSTING RING VOLUME
ADJUSTING RING VOLUME
Locate the adjustment controls on the back of the telephone labeled
RINGER1 and RINGER2 with LOW/HI.Slide the switch to the
desired LOW or HI ring volume for each line. (Two Line models
only).
For single line model, only one RIDNGER switch. Adjustment as
two line model.
14
14
PROGRAMMING MEMORY KEYS MANUALLY
PROGRAMMING MEMORY KEYS MANUALLY
14 PROGRAMMING MEMORY KEYS MANUALLY
14
PROGRAMMING MEMORY KEYS MANUALLY
To program the auto dial keys, the telephone must be connected to
a telephone line.
14.1 Lift handset or press [SPKR].
14.2 Press [STORE] Dial the number desired including [PAUSE]
and [FLASH] key where necessary, press [STORE] key again. The
sequence can be up to 16 digits in length.
14.3 Press a Memory key (including [MWL]) to finish.
14.4 Hang up the handset or press the [SPKR] key to disconnect
the telephone.
15
15
15
15 MESSAGE WAITING LIGHT
It is compatible high voltage neon/90V systems.
If there's message waiting, just press [MWL] key to play
messages.
[MWL] functions also as ringing indicator. Note: Only in
On-hook mode, press MWL to turn on the phone, press
AND
AND
AND
AND
SPEAKER
SPEAKER
SPEAKER
SPEAKER
the MWL again can keep the phone resume to on-hook
mode.
16
16
16
16
C C C C LONER
For initiative programming the one-touch memory keys
and MWL key with R.P. cloner, need do following to set
the "programming switch" :
16.1 Off-hook mode, press "*" key and last 5 seconds,
the phone set send out three dial tone continually and
Mute LED indicator flashing three times means this
device enter into programming mode if the phone set
with mute key.
16.2 Off-hook mode, press "#" key and last 5 seconds,
the phone set send out three dial tone continually and
Mute LED indicator flashing three times means this
device exit the programming mode if the phone set with
mute key.
16.3 When this device succeeds in programming, it will
exit the programming mode automatically. If the
programming fails and needs to quit the programming
mode. Just do as above 16.2 step. Programming again
need to open the programming device.
16.4 Passive programming and program with Hand-Held
cloner, no need to set the " programming switch". Detail
information for the cloner, please view their user manual
accordingly.
---- Page 7 of 10----
---- Page 7 of 10----
---- Page 7 of 10----
---- Page 7 of 10----
MESSAGE WAITING LIGHT
MESSAGE WAITING LIGHT
MESSAGE WAITING LIGHT
MESSAGE
MESSAGE
PROGRAMMING
PROGRAMMING
MESSAGE
MESSAGE
PROGRAMMING
PROGRAMMING
LONER
LONER
LONER
WITH
WITH
WITH
WITH