Epson 755c - PowerLite XGA LCD Projector Panduan Pengguna - Halaman 35

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Proyektor Epson 755c - PowerLite XGA LCD Projector. Epson 755c - PowerLite XGA LCD Projector 42 halaman. Release of check tool for network projectors v1.00 for windows
Juga untuk Epson 755c - PowerLite XGA LCD Projector: Panduan Pengoperasian (36 halaman), Lembar Spesifikasi (2 halaman), Manual Suku Cadang (26 halaman), Panduan Pengoperasian (47 halaman), Buletin Dukungan Produk (30 halaman), Item yang Dapat Diganti Pengguna (1 halaman), Pengaturan Cepat (2 halaman), Panduan Instalasi (19 halaman), Panduan Pengguna (1 halaman), Manual Fungsi (5 halaman), Buletin Dukungan Produk (25 halaman), Buletin Dukungan Produk (38 halaman), Buletin Dukungan Produk (12 halaman), Buletin Dukungan Produk (42 halaman), Buletin Dukungan Produk (22 halaman), Buletin Dukungan Produk (28 halaman), Buletin Dukungan Produk (41 halaman), Buletin Dukungan Produk (34 halaman), Buletin Dukungan Produk (38 halaman), Buletin Dukungan Produk (28 halaman), Buletin Dukungan Produk (15 halaman), Buletin Dukungan Produk (22 halaman)

Halaman Cetak

Epson 755c - PowerLite XGA LCD Projector Panduan Pengguna

E-mail notification function settings

The mail notification function can be used to send corresponding

notification messages to a preset e-mail address when a projector that is

connected to the network assumes a certain status, or if it experiences a

problem or warning. By using this function, the operator can be notified

of a projector's status or problems even when the operator is in a

different location from the projectors.

• Up to three addressees (destinations) can be registered and messages

can be sent to all of them at once.

• If a critical problem develops with a projector which causes it to

suddenly stop working, it may not be possible for the projector to send

a message notifying an operator of the problem.

• If Standby Mode is set to Network ON or Network Monitoring is set to

ON in the projector configuration menus, you can monitor the

projector even when it is in standby mode (when its power is turned

off). s Projector User's Guide

• On some projectors, the mail notification function can be set in the

configuration menu. When notification messages are set to be sent in

the projector's configuration menu, both the settings in the

configuration menu and settings made on EMP Monitor are

functional.

• Detectable status with the mail notification function differs with the

projector you are using.

Procedure

Select "Mail notification function" from the Tool menu.

The Set mail notification function window will be displayed.

Make the necessary settings while referring to the table below.

Mail notification

Set to ON to use the mail notification function.

function

SMTP server IP

Enter the IP address of the SMTP server. Up to

address

a maximum of 255 bytes can be entered.

When you change a port number of the SMTP

server, specify this port number. The default

value is "25".

You can enter a valid number from 1 to 65535.

Sender mail

Enter the sender's e-mail address. Up to a

address

maximum of 255 bytes can be entered.

Recipient mail

Specify the destination addresses for the

address 1

notification e-mail. Up to three destinations

can be set. Up to a maximum of 255 bytes can

Recipient mail

be entered.

address 2

Recipient mail

address 3