Epson 7900p - PowerLite XGA LCD Projector Pengaturan Cepat - Halaman 2

Jelajahi secara online atau unduh pdf Pengaturan Cepat untuk Proyektor Epson 7900p - PowerLite XGA LCD Projector. Epson 7900p - PowerLite XGA LCD Projector 2 halaman. Supplemental / late breaking information
Juga untuk Epson 7900p - PowerLite XGA LCD Projector: Panduan Pengguna (42 halaman), Panduan Pengoperasian (36 halaman), Suku Cadang Pengganti (1 halaman), Informasi Produk (24 halaman), Panduan Pengguna (1 halaman), Ringkasan Teknis (7 halaman), Buletin Dukungan Produk (7 halaman), Pemasangan Lensa (5 halaman)

Halaman Cetak
Epson 7900p - PowerLite XGA LCD Projector Pengaturan Cepat
A
djust the image
1
Rotate the focus ring to sharpen the image.
Focus ring
Zoom ring
NOTE:
If you see a blank screen
see the instructions to the right.
2
Rotate the zoom ring to reduce or enlarge the image. Turn to
W (wide) to enlarge or T (tele) to reduce. (You can also move
the projector closer to or farther from the screen.)
3
To raise the image, press up on the blue foot release lever for
the front adjustable foot. Lift the front of the projector. Once
the image is positioned where you want it, release the lever to
lock the foot in position.
4
If your image looks like
off to one side of the screen, at an angle. Move it directly in
front of the center of the screen, facing the screen squarely.
5
If your image looks like
feature has been disabled. You can manually adjust the keystone
correction value by pressing the
projector. Or, to enable Auto Keystone correction, see your User's Guide.
W
here to get help
Telephone Support Services
To use the EPSON PrivateLine
and enter the PIN on the EPSON PrivateLine Support card included in
your Start Here kit. This service is available 6
Monday through Friday, for the duration of your warranty period.
You may also speak with a projector support specialist by dialing
one of these numbers:
U.S.:
(562) 276-4394, 6
Monday through Friday
Canada: (905) 709-3839, 6
Monday through Friday
Toll or long distance charges may apply.
Electronic Support Services
EPSON provides technical assistance through electronic support
services 24 hours a day at http://support.epson.com. For tips,
templates, and training for developing successful presentations
go to http://www.presentersonline.com.
Epson is a registered trademark and EasyMP is a trademark of Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners.
Epson disclaims any and all rights in those marks. © 2004 by Epson America, Inc. Printed in XXX. 8/04
after focusing,
No signal (
?
Help)
Front adjustable
foot
or
, you've placed the projector
or
, the Auto Keystone correction
or
Sync buttons on the
®
Support service, call (800) 637-7661
to 6
, Pacific Time,
AM
PM
to 6
, Pacific Time,
AM
PM
to 6
, Pacific Time,
AM
PM
EPSON
PowerLite
®
T
roubleshooting
If you see a blank screen...
If you see a blank screen or the No signal message
after turning on your notebook, check the following:
Make sure the
power light on the projector is
green and not flashing and the lens cover is off.
Try turning off the notebook and restarting it.
If you've only connected your notebook to the projector and you've
used the VGA computer cable, press the Comp button on the remote
control. If you've connected more than one computer and/or video
source, press the button on the remote control for your image source
(Comp, DVI, BNC, S-Video, or Video). Allow a few seconds for the
projector to sync up after pressing it.
Note:
The EasyMP button is not functional on the PowerLite 7800p.
If the projector and notebook
don't display the same image...
If your image displays either on the projector or notebook, but not on
both, check the following:
Windows
Hold down the Fn button and press the function key that lets you
display on an external monitor. It may have an icon such as
or it may be labeled CRT/LCD. Allow a few seconds for the projector
to sync up after pressing it.
On most systems, the
screen and the projector, or display on both at the same time.
You might need to use the Display utility in the Windows Control
Panel to enable both the LCD screen and external monitor port.
Check your notebook's manual or online help for details.
Macintosh
®
OS X
1.
From the Apple
®
menu,
select System Preferences,
then click Displays.
2.
Select the VGA Display or
Color LCD dialog box, click the
Arrange (or Arrangement) tab,
and make sure Mirror Displays is checked.
Macintosh OS 9 or earlier
1.
From the Apple menu, select
Control Panels, then click
Monitors or Monitors and Sound.
2.
Click the Arrange icon,
then drag one monitor
icon on top of the other.
This lets you display on the
projector screen as well as the LCD screen.
3.
If the Arrange option isn't available, click the Monitor icon
and select a Simulscan resolution.
Quick Setup
7900p
®
No signal (
?
key lets you toggle between the LCD
Click here
Make sure
this is checked
Click here
Drag one monitor
icon on top of
the other
Help )
,
CPD-18738