Alignment
Intense noise formation, vibrations and "wandering" may be the result of incorrect
alignment.
Aligning the washing machine with a spirit level
1. Loosen the lock nut using a wrench, by turning it in a clockwise direction.
2. Change the height by turning the appliance feet.
Caution: all four appliance feet must be firmly on the ground.
The washing machine must not wobble.
Check the alignment of the washing machine with a spirit level and adjust
if necessary.
3. Tighten the lock nut against the housing.
In doing so, hold the foot tight and do not adjust its height.
Caution: the lock nuts on all four appliance feet must be screwed tightly
against the housing.
Electrical connection
The washing machine must only be connected to an alternating current via a
properly installed earthed socket.
The power supply and voltage indicated on the washing machine (rating plate)
must be the same.
The connected load and fuse required are specified on the rating plate.
Make sure that:
– the mains plug fits the socket,
– the cable cross-section is adequate,
– the earthing system is properly installed.
(If this is necessary), the mains cable may only be replaced by a qualified
electrician.
Replacement mains cables are available from the after-sales service.
Do not use multiple plugs/couplings or extension cables.
If a residual current circuit breaker is used, only use a type which displays this
symbol: ‚.
Only this symbol guarantees compliance with the currently applicable regulations.
Do not plug in or unplug the mains plug with wet hands.
Pull the appliance plug out of the socket at the plug only, not by the cable.
Manufacturer –> Operating instructions
Transportation, e.g. when moving home
1.
Before transporting the washing machine:
1. Turn off the tap.
2. Drain residual water
Operating instructions; Maintenance - drain pump.
3. Release the water pressure in the inlet hose
Operating instructions; Maintenance - filter
in water inlet.
4. Disconnect the washing machine from the power supply.
5. Dismantle the hoses.
2.
Preparing and installing transport braces:
1.
Remove all covers and store them.
2.
Affix all transport braces. In doing so, turn the
bend on the hose holders inwards. Clamp the
mains cable in the holders. Tighten the screws.
After transportation, the transport braces must be removed.
page 3.
To prevent unused detergent from flowing straight into the drain during the next wash: Pour
2 litres of water into compartment II and start the Empty programme.
Technical specifications
Dimensions (width x depth x height)
60 x 55 x 85 cm
Weight
66 – 73 kg depending on model
Nominal voltage 220-240 V, 50 Hz
Mains connection
Nominal current 10 A
Nominal power 2,300 W
Water pressure
200-1000 kPa (2-10 bar)
5
After-sales service
If you cannot rectify the fault yourself (Operating instructions; What to do if...
please contact our after-sales service. We will always find a suitable solution and will avoid a
visit from a service technician wherever possible.
The contact details for all countries can be found in the enclosed after-sales service directory.
Please give the after-sales service the product number (E-Nr.) and the production number
(FD) of the appliance.
You will find this information on the inside of the
washing machine door, on the opened service
flap or at the rear of the appliance (depending
on the model).
Product number
Production number
Rely on the professionalism of the manufacturer. Please contact us.
This will ensure that the repair is carried out by trained service technicians who arrive
equipped with genuine spare parts for your appliance.
Aqua-Stop warranty
only for appliances with Aqua-Stop
In addition to warranty claims against the vendor from the purchase agreement and to our
appliance warranty, we will pay damages under the following conditions:
1. If a fault in our Aqua-Stop system causes water damage, we will reimburse damages caused
to private customers.
2. The liability guarantee is valid for the service life of the appliance.
3. It is a prerequisite of all warranty claims that the appliance with Aqua-Stop must have been
set up and connected correctly in accordance with our instructions; this also includes a
correctly fitted Aqua-Stop extension (original accessories).
Our warranty goes not cover defective power cables or fittings between the Aqua-Stop
connection and the tap.
4. Appliances with Aqua-Stop do not need to be supervised during operation, nor secured
afterwards by turning off the tap.
The tap only needs to be turned off if you are away from home for a long period, e.g. for
several weeks' holiday.
6
page 11),
Washing machine
Installation
instructions
Contents
Page
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . 1
Installation surface. . . . . . . . . . . . . . . . . . . . . . . . . 1
Installing the appliance . . . . . . . . . . . . . . . . . . . . . 1
Scope of delivery. . . . . . . . . . . . . . . . . . . . . . . . . . 2
Hose and cable lengths . . . . . . . . . . . . . . . . . . . . 2
Removing the transport braces . . . . . . . . . . . . . . . 3
Water connection . . . . . . . . . . . . . . . . . . . . . . . .3/4
Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . 5
Transportation, e.g. when moving home . . . . . . . . 6
Technical specifications. . . . . . . . . . . . . . . . . . . . . 6
After-sales service . . . . . . . . . . . . . . . . . . . . . . . . . 7
Aqua-Stop warranty . . . . . . . . . . . . . . . . . . . . . . . . 7
Read these instructions before switching on the washing machine.
Also observe the separate Instruction manual.
Keep all documents for use in the future or for the subsequent owner.
7
en
Halaman Cetak