Cisco 8800 Series Panduan Utama Migrasi Firmware - Halaman 15

Jelajahi secara online atau unduh pdf Panduan Utama Migrasi Firmware untuk Telepon IP Cisco 8800 Series. Cisco 8800 Series 31 halaman. Hosted enterprise uc ip phone
Juga untuk Cisco 8800 Series: Panduan Pemasangan Perangkat Keras (25 halaman), Panduan Pengguna (4 halaman), Mulai Cepat (2 halaman), Manual (10 halaman), Panduan Memulai Cepat (3 halaman), Panduan Memulai Cepat (2 halaman), Mulai Manual (2 halaman), Panduan Pengguna (24 halaman), Referensi Cepat (2 halaman), Panduan Pengguna (28 halaman), Panduan Memulai Cepat (3 halaman), Panduan Pengguna (2 halaman), Panduan Pengguna (30 halaman), Panduan Memulai Cepat (2 halaman), Panduan Memulai Cepat (2 halaman), Manual (44 halaman), Manual (13 halaman), Manual (14 halaman), Manual (4 halaman), Manual (4 halaman), Memulai (6 halaman), Panduan Memulai Cepat (19 halaman), Panduan Pemeliharaan (6 halaman), Mulai Cepat (2 halaman), Panduan Pengguna Cepat (2 halaman), Panduan Pengguna Akhir (6 halaman), Panduan Memulai Cepat (2 halaman), Tembak Masalah (4 halaman), Panduan Referensi Cepat (7 halaman), Panduan Memulai Cepat (2 halaman), Manual (22 halaman), Manual (22 halaman), Panduan Memulai Cepat (2 halaman), Panduan Memulai Cepat (2 halaman), Panduan Memulai Cepat (2 halaman), Panduan Memulai Cepat (2 halaman), Panduan Memulai Cepat (2 halaman), Panduan Memulai Cepat (2 halaman), Manual (48 halaman), Panduan Pengguna (40 halaman), Panduan Memulai Cepat (2 halaman), Panduan Memulai Cepat (2 halaman), Panduan Memulai Cepat (2 halaman), Panduan Memulai Cepat (2 halaman), Panduan Memulai Cepat (2 halaman)

Halaman Cetak
Cisco 8800 Series Panduan Utama Migrasi Firmware
9.
After reboot, you will be on the transitional load. You will see "Configuration check in progress" and you may see a warning "Failed
to download configuration. Contact your administrator." Do NOT click "Retry". If you click "Retry" the phone will reboot and display
the warning message again. The warning message pertains to Bulk Provisioning. Bulk provisioning is covered in the Appendix.
10. Determine the IP Address of your phone via Settings -> Status -> Network Status -> IPv4.
11. Type the following into your web browser:
12. In your web browser, navigate to Voice -> Provisioning.
13. Scroll down to "Firmware Upgrade" and paste the following into the "Upgrade Rule":
Upgrade Rule:
http:// CUCM-ip-address:6970/sipxxxx.12-5-1SR1-4.loads
Note: This Upgrade Rule points to 12.5(1). This is an Enterprise Firmware image than can be registered to the Unified CM.
14. Scroll down to "Firmware Upgrade" and paste the following into the "Transition Load Authorization Rule".
Transition Load Authorization Rule:
Example Upgrade Rule and Transition Load Authorization Rule:
15. After saving, you should soon see the following message indicating success:
16. After successful upgrade, register the phone to CUCM using DHCP Option 150 or Alternate TFTP.
a)
Select Settings -> Admin Settings -> Network Setup -> IPv4 Setup
b)
Click Apply.
c)
Validate that the phone has registered to Unified CM.
MPP to Enterprise firmware conversion is now complete!
© 2015 Cisco and/or its affiliates. All rights reserved. This document is Cisco Internal Information.
http://ip_address_of_phone/admin/advanced
http:// CUCM-ip-address:6970/$MAU_M2E.lic
• Alternate TFTP: Yes
• TFTP Server 1: CUCM-IP-address
where sipxxx is the firmware filename on the Unified CM.
Page 15 of 30