Ricoh StreamPunch Pro EX Panduan Pengoperasian & Instruksi - Halaman 7

Jelajahi secara online atau unduh pdf Panduan Pengoperasian & Instruksi untuk Printer Ricoh StreamPunch Pro EX. Ricoh StreamPunch Pro EX 32 halaman.

Ricoh StreamPunch Pro EX Panduan Pengoperasian & Instruksi
8. PAPER CHIP DRAWER
The paper chip drawer for your StreamPunch is located at the front of
the machine's base. The drawer should periodically be pulled out and
emptied. The StreamPunch incorporates microprocessor technology
to inform the operator when the Chip Tray needs to be emptied. When
the Punch has cycled a certain number of times or the chip tray level
has reached the top of the tray, the Check Chip Tray LED will start to
flash on and off. You may continue to use the StreamPunch for a short
while longer if you wish, but it is not recommended.
You must empty the Chip Tray with the Power On so that the sensors
are able to identify this action. This will ensure that the LED will reset
itself.
9. SERVICE
 Should your StreamPunch require service, contact your local
authorized service representative.
 There are NO user-serviceable parts inside the machine. To avoid
potential personal injury and/or property damage, DO NOT REMOVE
THE MACHINE'S COVER.
 It is recommended that your StreamPunch receives preventive
maintenance every 6 months or sooner depending on usage.
 To conserve the life of the Die Sets, you should apply a coating of light
machine oil at least once every 50 thousand punches (every 250
thousand punches for High Durability die sets). Apply the oil to the
exposed wick/felt material near the pin or any marked oil hole. Do not
use spray lubricants.
 Oil from the die sets may blemish the first few copies when the machine
is first used, and when machine oil has been freshly applied. In this
case, please keep test copying until clean copies can be made.
10. PROBLEM SOLVING
Probable Cause
No power, won't punch
Die Set will not come out using
a moderate pull
Probable Cause
Power cord not attached to back of
machine or not properly plugged into
the wall. Power On/Off Switch not
activated
The Die Set is in partial cycle. Turn
the Die Set knob (J3) to the HOME
position. Home position is when the
arrows line up. The Die Set should now
slide out easily.
Also see Paper Jams.
StreamPunch
11. SPECIFICATIONS
Speed
Punch Sheet Size
Punch Edge
Paper Stock
Paper Bypass Mode
Sheet size
Punch Capacity
Power Supply
Electrical
Safety Certification
Dimensions
Weight
Shipping Weight
Manufactured
Guarantee
Operation of this machine is guaranteed for one year from date of purchase,
subject to normal use. Within the guarantee period, GBC, using their
discretion, will either repair or replace the defective machine free of charge.
Defects due to misuse or use for inappropriate purposes are not covered
under the guarantee. Proof of date of purchase will be required. Repairs
or alterations made by persons not authorised by GBC will invalidate the
guarantee. It is our aim to ensure that our products perform to the
specifications stated. This guarantee does not affect the legal rights that
consumers have under applicable national legislation governing the sale
of goods.
Pro, Pro EX & MP
TM
230V Machines
Up to 135 sheets per minute
A4 - 210mm x 297mm
297mm
75gsm to 216gsm
Paper sizes and stocks same as
printer
Single Sheet
230V, 50Hz,
Single Phase
BTUs/Hour
1160BTU/HR
Watts
240W
Amps
1.3A
TUV/GS, CE according to
EN60950-1:A11 IEC60950-1
30.5cm (12") (W) x 97.8cm
(38.5") (H) x 72.3cm (28.5") (D)
70 Kg (154 lbs.)
115.5 Kg (254 lbs.)
Assembled in Taiwan
GB
7