Ricoh Aficio AP400 Panduan Instalasi Cepat - Halaman 2
Jelajahi secara online atau unduh pdf Panduan Instalasi Cepat untuk Aksesori Printer Ricoh Aficio AP400. Ricoh Aficio AP400 2 halaman. Sap printing
Juga untuk Ricoh Aficio AP400: Panduan Petunjuk Pengoperasian (20 halaman), Panduan Instalasi (4 halaman), Panduan Petunjuk Pengoperasian (30 halaman), Manual (12 halaman)
Halaman Cetak
CONNECTING THE POWER
SELECTING THE PANEL
CORD
DISPLAY LANGUAGE
Select a language following the procedures
Caution
described.
• When you pull the plug out of the socket, grip
the plug to avoid damaging the cord and caus-
The message for the selected language will
ing a fire or an electric shock.
appear on the panel display.
• It is dangerous to handle the plug with wet
hands. An electric shock might occur.
Note
The default setting is English.
Check that the power switch is turned off.
If you want to use the English panel display, the
following procedures are unnecessary.
Check that the power switch is turned on.
Press the {Menu} key.
ZKEH205E
Job Reset
Securely insert the power cord plug into the wall
socket.
Form Feed
"Menu" appears on the panel display.
Press the { } or { } key until the following
message appears on the panel display.
Menu:
Language
Press the {Enter
Press the { } or { } key until the language
you want to select appears on the panel display.
Press the {Enter
Press the {Online f} key.
The settings are applied and the ready message appears on the panel
display.
PRINTING A CONFIGURATION
PAGE
You can check if the printer works properly by
printing a configuration page.
However, you cannot check the connection
between the printer and the computer by printing
the configuration page.
Check that the power switch is turned on.
Press the {Menu} key.
"Menu" appears on the panel display.
Press the { } or { } key until the following
Menu
On Line
message appears on the panel display.
Menu:
Escape
List/Test Print
Enter
Press the {Enter
The following message appears on the panel display.
Power
Error
Data In
List/Test Print:
Config. Page
Press the {Enter
The test printing will start.
Important
If you cannot complete the test printing correctly,
check if an error message appears on the panel
} key.
display. For more information about error
messages, see "Troubleshooting" in the Printer
Reference provided as a PDF file on the CD-ROM
labeled "Operating Instructions".
} key.
CONNECTING THE PRINTER TO A COMPUTER
Network connection
If your printer is installed with the Network Interface
Board, follow the procedures below.
Turn off the power switch.
Loop the network interface cable and attach
the ferrite core.
Note
The network interface cable loop should be about
15 cm(6")(
) from the end of the cable (on the
end closet to the printer). The ferrite core at the
end of the cable should be a ring type ferrite core.
} key.
Attach the network interface cable to the
jack on the board.
} key.
Connect the other end of the network interface
cable to the network.
Turn on the power switch.
Check the LEDs on the ethernet port.
1
2
ZKDH260E
1 is lit when the printer is securely connected to the network.
2 is lit when 100BASE-TX is in use and not lit when 10BASE-T is in
use.
Parallel connection
Important
The parallel interface cable is not provided with
the printer. Make sure that the interface cable
you use is appropriate for your computer.
The printer's parallel connection is a standard
bi-directional interface. It requires a standard
36-pin parallel cable compliant with IEEE 1284
and an available parallel port on your computer.
To avoid electrical interference, use a shielded
cable.
Note
Do not use a parallel cable more than 2.5 meters
(8.2 feet) long.
Turn off the power switch.
Turn the computer off.
ZKEH126E
Attach the interface cable to the interface con-
nector of the printer. Secure the cable with the
metal fittings as shown in the illustration.
ZKEX291E
ZKEX115E
Attach the other end of the interface cable to
the interface connector of the computer. Se-
cure the cable.
Important
Rating voltage of the parallel interface connector
for the computer ; Max. DC5V.
USB connection
Important
The USB interface cable is not provided with the
printer. Make sure that the USB interface cable
you use is appropriate for your computer.
Attach the USB interface cable to the USB
interface connector of the printer. Secure the
cable.
ZKET300E
Attach the other end of the interface cable to
the USB interface connector of the computer
or the USB Hub. Secure the cable.
Note
USB connection is possible with Windows 98 SE/
Me, Windows 2000/XP, Mac OS 9.x and Mac OS
X.
When using Windows 98 SE/Me, install the "USB
Printing Support" software. The support speed
with Windows 98 SE/Me is equivalent to USB 1.1.
USB connection with Macintosh is only possible
via the standard USB port on the printer body.
The support speed with Macintosh is equivalent
to USB 1.1.
SETTING UP FOR PRINTING
Printing requires installation of a printer driver
for the operating system.
Reference
See "Printer Drivers for This Printer" in the
Setup Guide.
If you want to install options, see "Installing
Options" in the Setup Guide.
Copyright © 2003 G095-8627
Printed in China
EN USA