c3controls 900-SBA8I4OM Buku Petunjuk - Halaman 12

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Relai c3controls 900-SBA8I4OM. c3controls 900-SBA8I4OM 17 halaman. Smart programmable relays

Halaman Cetak

SERIES 900 SMART PROGRAMMABLE RELAYS

WORKING WITH SPR-SOFT III

TO SET & REMOVE PASSWORD

1. Select the Configuration >Device Utilities menu command. The Device

Utilities window will appear.

2. Click on set password.

3. Enter four digit passwords into the two boxes "New Password" and

"Confirm New Password" then confirm with OK.

4. You can delete your assigned password at any time. To do this, enter the

existing password in the "Old Password" box, then confirm with OK.

5. To change the password, you must first enter the new password in the two

boxes "New Password" and "Confirm Password" and the existing password

in the Current Password text box. Then confirm with OK.

TO SET BACKLIT MODE

1. Select the Configuration >Device Utilities menu command. The Device

Utilities window will appear.

2. Select the mode Auto, On or Off then click on the set mode button.

3. The requested operation will move the device out from the run mode. The

message "Do you want to continue?" will appear.

4. By pressing Yes, the backlit mode will be set and the message "Backlit

mode has been set successfully" will appear.

TO CONFIGURE COMMUNICATION PORT

1. Select the Options > Comm port menu command. The COM Port settings

window will appear with two option buttons to select the Port.

2. Select "Device is connected to USB Port" when the device is connected

with a cable.

3. Select "Device is connected to Serial Communication Port" when the

device is connected with a Serial Communication cable.

TO SET COMMUNICATION PARAMETERS

1. Select the Options > Comm port menu command. The COM Port setting

window will appear.

2. The user can set the following communication parameters:

SLAVE ID:

Selectable from 1 to 247

BAUD RATE: Selectable as 1200, 2400, 4800, 9600 baud

PARITY:

Selectable as NONE, EVEN and ODD

STOP BIT:

Selectable as 1 and 2 Stop Bits

CLOCK SETTING

1. Select the Transfer > Device Clock menu command. The Device Clock

window will appear.

2. To view the Date and Time of the device: Click Read button on the clock

setting window.

3. To set the Date and Time in the device: User can select Date and Time to

write into the device. Click Write button on the clock setting window.

WE DIDN'T INVENT CONTROL, WE'RE PERFECTING IT.

DST (DAYLIGHT SAVINGS TIME) SETTING

1. Select the Transfer > Device Clock menu command. The Device Clock

window will appear.

2. To set Enable DST, Select "Click Daylight Saving Time" the DST setting

section will now be visible.

3. User can select the following parameters: Begin Week, Begin Day, Begin

Month, Begin Time, End Week, End Day, End Month, End Time, Offset Time.

4. To set Disable DST:

· Deselect Daylight Saving Time option and the DST window will be

disabled.

· Press Set DST.

5. To read DST: Press Read DST, independent of the DST enable or disabled.

TRANSFER OPTIONS

PC to Device

1. Select the Transfer > Program menu command. The transfer window will

appear.

2. Press "PC to Device" button on transfer dialog box. Current program on the

screen will be transferred to the device.

3. Transfer completion message "The Program is downloaded successfully"

will appear on the screen.

Device to PC

1. Select the Transfer > Program menu command. The transfer window will

appear.

2. Press "Device to PC" button on the transfer dialog box. Current program on

the screen will be transferred to the device.

3. Transfer completion message "The Program is downloaded successfully"

will appear on the screen.

4. Read program will be shown on the main screen.

Expansion Module Selection

1. Select the Configuration >PLC Model menu command. The Model

Selection window will appear.

2. Selection of the Series 900 relay model and Expansion modules. Maximum

three expansion modules can be connected to one Series 900 relay.