CABASSE 30ND40 Panduan Petunjuk Pengoperasian - Halaman 6

Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Subwoofer CABASSE 30ND40. CABASSE 30ND40 10 halaman. Santorin 30
Juga untuk CABASSE 30ND40: Brosur (1 halaman)

Halaman Cetak

e n g l i s h

POSITIONING

Speakers positioning

Our speakers have been designed to function in a vertical position.

The majority of our models are delivered with a set of decoupling

spikes or cones, these accessories are to be screwed in the inserts

under the cabinets. These accessories ensure the stability of the

speaker while limiting resonance coming from certain types of

grounds like wood floors.

Powerful drivers generate magnetic fields that can extend beyond

the boundaries of the speaker cabinet. We recommend you keep

magnetically sensitive articles (TV, computer screen, computer

discs, audio and video tapes, swipe cards...) at least 1.5 ft (50 cm)

away from the speaker. Cabasse centre speakers or the ones mar-

ked «TV» are not concerned with this, being magnetically shielded.

Positioning speakers in a room

Optimal positioning for a 2.1

or stereo with a subwoofer system

For a stereo listening with 2 speakers or 2 satellites and 1 sub-

woofer, we recommend you to place the subwoofer in the front lis-

tening area. The placement of the subwoofer against a wall reinforces

the low frequencies and limit the reflections from 80 to 200 Hz.

However to obtain the best results, it is always necessary to carry out

tests according to the acoustic of the room.

Optimal positioning for a 5.1

or home theatre system

Setting up a multi-channel Audio-Video system requires great care

when positioning the specific AV speakers.

The centre speaker should be placed as close as possible to the

screen and where it sounds best from your listening spot while offe-

ring the optimal picture/dialogue cohesion. Theoretically, the screen

should be located within a virtual triangle formed by the acoustical

centres of the main speakers and the centre speaker. Practically

speaking, this means that the principal speaker should be placed abo-

ve the screen if the main speakers are below it, and below the screen

if the main speakers are above. The centre speaker should also, if pos-

sible, be set slightly back from the others, so that it is located at the

same distance from the listener as the main speakers.

The rear speakers or surround should be placed against the side

walls, at listening height. They should not be positioned far behind

the listening zone.

The subwoofer should be placed in the front listening area, its posi-

tion against a wall reinforces the extreme low register and limits

the reflections between 80 and 200 Hz. However to obtain the best

result, it is always necessary to carry out tests according to the

acoustics of the room.

Your AV processor enables the adjustment in level and delay of

each of the 5/6/7 channels of your system. Fine-tuning is necessa-

ry to obtain a perfect sound stage.

Turn off all the amplifiers before connecting them to the loud-

speakers. In order to connect loudspeakers properly, it is most

important to keep in mind the following two factors: cable section

and phase.

CONNECTION

Cable section

To get the full sonic poten-

tial of Cabasse loudspea-

amplifier and loudspeakers

kers and avoid power

losses, the cables connec-

ting the speakers to the

power amplifier must have

the lowest possible electri-

cal resistance. To help you

in choosing the correct cable gauge, follow diagram.

Phase

In order to maintain the phase relationship and frequency balance of the

loudspeaker system, both loudspeakers must be properly connected to

the power amplifier. When properly connected, the cones of the drivers

of both loudspeakers will move in the same direction when driven by the

same signals. If the cones move in opposite directions, the resulting out

of phase signals will create a perceptible power loss, particularly in the

low frequencies. The stereophonic message will also be degraded. Ampli-

fier and speaker manufacturers typically indicate connection polarity

in one of two ways: red and black or plus and minus. In either case, always

connect red or plus to red or plus and black or minus to black or minus.

Connections should be identical for both channels. To check that the

speakers are in correct phase, switch the system to mono while music

is being played. if the amplifier does not have a phase inversion switch,

it will be necessary to change over the connections on one only of the loud-

speakers. If in correct phase, the image should be distinctly located bet-

ween the loudspeakers with a slight loss of bass and low midrange level.

If the image is confused and not centrally located and there is a drastic

loss of bass and low midrange level, recheck your connections.

Power management

Select the right voltage with the 115 V –

230 V

switch and connect the

plug to the mains with a 700 W or more

power chord cable (3 A / 230 V, 6 A /

115 V). Then power on the amplifier

with the

switch. Finally press the

POWER key of the remote control or

any key on the front pad to get the sys-

tem on play mode. The display will be

activated after 3 to 4 seconds.

SETTINGS

I) THE AJUSTABLE PARAMETERS

USE OF THE FRONT PANEL PAD:

The 5 keys on the front panels of the Santorin 30 give access to all the

here-under adjustable parameters.

" and " → " (TP6 et TP3) keys to select the parameters,

Use the "

then select the right option or value thanks to the "

et TP3) keys. The "ENTER" (TP1) key must be pressed down to confirm

a setting and/or answer to "ENTER ?" and " VALIDATE ?".

Lenght between

recommended

section

4.5 m

1.5 mm

6 m

2 mm

7.5 m

2.5 mm

9 m

3 mm

12 m

4 mm

Attention,

before operating the unit,

be sure that the

operating voltage

of your unit is identical

with that of your local

power voltage.

" et "→ " (TP6