Cisco 7841 Panduan Konfigurasi Ulang

Jelajahi secara online atau unduh pdf Panduan Konfigurasi Ulang untuk Sistem Konferensi Cisco 7841. Cisco 7841 2 halaman. Classroom phone
Juga untuk Cisco 7841: Catatan Rilis (16 halaman), Panduan Memulai Cepat (2 halaman), Panduan Referensi Cepat (4 halaman), Referensi Cepat (4 halaman), Instalasi Cepat & Panduan Pengguna (12 halaman), Panduan Referensi (11 halaman), Panduan Referensi Cepat (7 halaman), Panduan Referensi Cepat (7 halaman), Panduan Pengguna (2 halaman), Panduan Referensi Cepat (2 halaman), Panduan Referensi Cepat (2 halaman), Manual (2 halaman), Manual (27 halaman), Panduan Utama Migrasi Firmware (31 halaman), Manual (43 halaman), Panduan Referensi Cepat (4 halaman), Panduan Memulai Cepat (2 halaman), Panduan Instalasi (39 halaman), Menggunakan (4 halaman), Panduan Pengguna Cepat (2 halaman), Manual (7 halaman), Manual (20 halaman), Panduan Fitur (4 halaman), Panduan Referensi Pengguna (5 halaman), Kartu Referensi Cepat (2 halaman), Panduan Instalasi Cepat (12 halaman), Panduan Memulai Cepat (2 halaman), Panduan Cepat (3 halaman), Kartu Referensi Cepat (2 halaman), Kartu Referensi Cepat (2 halaman), Panduan Memulai Cepat (2 halaman), Panduan Referensi Cepat (3 halaman)

Halaman Cetak

WARNING:

THIS PROCEDURE DESCRIBES HOW TO MANUALLY RE-

CONFIGURE A CISCO MPP IP PHONE TO WORK ON THE BROADSOFT

BROADCLOUD PBX NETWORK.

COMPLETED, ANY PRIOR CONFIGURATION SETTINGS ON THE DEVICE WILL

BE OVERRIDDEN, INCLUDING THE ADMINISTRATOR PASSWORD, AND THE

DEVICE WILL ONLY BE USABLE ON THE BROADSOFT BROADCLOUD PBX

NETWORK. THE DEVICE MUST BE RETURNED TO THE CISCO FACTORY

DEFAULT CONFIGURATION BEFORE IT CAN BE USED ON ANY NETWORK

OTHER THEN BROADSOFT BROADCLOUD PBX.

Notes:

1. For Cisco 6821, 6841, 6851, 7811, 7821, 7832, 7841, 7861, 8811, 8832,

8841, 8845, 8851, 8861 and 8865 IP Phones, please upgrade your phone to

11.2.3 MPP or higher before connecting to the BroadCloud Platform.

Procedure:

1. Factory reset the phone before attempting to connect to the BroadCloud

platform.

2. Press the setup button on the device

3. Press the down arrow till "Status" is selected and press the "Select" soft

key.

4. Press down arrow till "Network Status" is selected and press the "Select"

soft key.

5. Record the IP address under from the "IPv4 status" option.

6. From a browser on the same LAN, enter the IP address recorded in step 5

7. Click the "Admin Login" link in the top right of the page

8. Click the "Advanced" link in the top right of the page

9. Click the "Voice" tab

10. Click the "Provisioning" tab

11. Enter the following link in "Profile Rule"

Region

North America

Europe

Australia

Japan

12. Select "Submit All Changes" at the bottom of the page

13. Wait for about 10 minutes for the new configuration to download. The

phone will undergo a few reboot cycles for the complete configuration to

download.

ONCE THIS PROCEDURE HAS BEEN

Device Management URL

https://cisco.sipflash.com/

https://cisco.broadcloud.eu/

https://cisco.broadcloud.com.au/

https://cisco-jp.bcld.webex.com/

Cisco MPP Phones

Manual Reconfiguration Guide

(See ** if problems)