ACU-RITE 736 Buku Petunjuk - Halaman 2
Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Stasiun Cuaca ACU-RITE 736. ACU-RITE 736 2 halaman. Wireless weather station with sensor
MIN/MAX/MEMORY:
The main unit automatically stores the high and low temperature.
Pressing the max/min button will display the maximum
temperature for 5 seconds. Press the button again to display
the minimum temperature for 5 seconds.
To clear the stored temperature, press the clear button while
the value you wish to clear (max or min) is displayed.
TEMPERATURE ALERT:
Minimum and maximum temperature alerts can be programmed.
To turn the feature on or off, press the alert button. When the
icon is displayed this feature is on.
Setting Cycle:
To set the temperature at which the alert will sound, press the
alert button for 3 seconds until the outdoor temperature and
the upper/lower icon flash. Press the + or - button to select the
desired channel; press the alert button to confirm the channel
selection.
The upper pointer and temperature will begin to flash. Enter
the desired upper limit temperature by pressing the +/- buttons;
press alert to confirm.
The lower pointer and temperature will begin to flash. Enter
the desired lower limit with the +/- buttons; press alert to
confirm and exit the temperature alert mode.
When the temperature reaches either the upper or lower limit,
the pointers and the temperature begin to flash and an alarm
will sound. Press any key to stop the alarm. The temperature
will continue to flash until the temperature changes from the
upper or lower limit temperature.
TIME:
Clock and Calendar Setting:
Press the set button for 3 seconds to enter the clock setting
mode. Use the + or - buttons on the back of the main unit to
adjust settings. Press the set button to confirm each setting.
The settings will be in the following sequence:
12/24 hour mode
Hour and minute settings
Hour offset allows the time to be set ahead (to maintain
correct time, keep at 0)
Year, day and month.
Alarm Setting:
Press the clear button for 3 seconds. Press + or - to enter the
desired hour. Press clear again and use the + or - to enter the
desired minutes. Press clear again to confirm the time for the
alarm.
A bell icon will appear in the time panel to show that the alarm
is set. To view the time the alarm is set for, press the clear
button. The alarm time will display for 5 seconds and then
switch back to normal clock mode.
When alarm goes off, the alarm will sound for 1 minute. Each
time you press the snooze button the alarm will "snooze" for
ten minutes, and then sound again.
To turn the alarm and snooze alarm off, press the + button.
TROUBLESHOOTING:
At times, the main unit may display "---" in the remote
temperature if outside interference is occurring. Most of the
time the unit will re-sync the signal on it's own. However, if this
should continue to occur, the following may also be the reason:
A.
Low battery indicator(s).
B.
The sensor has been placed outside of the effective
transmission range (more than 100 feet). Move the
sensor closer to the main unit.
C. Sensor units may have outside interference that is
preventing proper transmission. Sources of interference
include but are not limited to metal surfaces, electrical
devices, etc. The sensor may need to be relocated if
interference continues.
The weather forecasting feature relies on barometric trend
changes for its forecasts, which produces results that are
accurate 70-80% of the time. The weather forecasting feature
predicts conditions up to 12 hours in advance. If the
forecasting icon is not updating according to the weather,
recalibrate the main unit (see initial set-up procedures).
LIMITED WARRANTY: Should this product from the
Chaney Instrument Co. prove to be defective in material or
workmanship within one year of original purchase it will be
repaired or replaced. This warranty does not cover damage
in shipment or failure caused by tampering, carelessness,
.
or abuse
CHANEY INSTRUMENT CO.
LAKE GENEVA, WISCONSIN 53147
www.chaneyinstrument.com