Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion Manual - Halaman 16

Jelajahi secara online atau unduh pdf Manual untuk Perangkat Keras Jaringan Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 19 halaman. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Juga untuk Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion: Catatan Instalasi (14 halaman), Panduan Solusi (17 halaman), Catatan Instalasi (46 halaman), Buku Putih (19 halaman), Deskripsi (1 halaman), Buletin Produk (6 halaman), Pemberitahuan (4 halaman), Lembar data (9 halaman), Lembar data (18 halaman), Buku Putih (18 halaman), Panduan Konfigurasi (8 halaman), Catatan Instalasi (28 halaman), Panduan Pemecahan Masalah (11 halaman), Catatan Instalasi (18 halaman), Panduan Pengguna (17 halaman), Catatan Instalasi (24 halaman), Catatan Instalasi (36 halaman)

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion Manual
Cisco - Connecting a Terminal to the Console Port on Catalyst Switches
Mode 2: Switch is in the out position. Use this mode to connect a terminal to the console port
using the Catalyst 5000 family Supervisor Engine III console straight-through cable and an
appropriate adapter for the terminal connection (cable and adapter are not provided). See
Port Mode 2 Signaling and

Console Port Mode 1 Signaling and Pinouts

This section provides the signaling and pinouts for the console port in mode 1 (port mode switch in the in
position).
DB-9 Adapter (for Connecting to a PC)
Use the RJ-45-to-RJ-45 rollover cable and the RJ-45-to-DB-9 female DTE adapter (labeled
"Terminal") to connect the console port to a PC running terminal emulation software.
lists the pinouts for the asynchronous serial console port, the RJ-45-to-RJ-45 rollover cable, and
the RJ-45-to-DB-9 female DTE adapter.
Table I-1: Port Mode 1: Console Port Signaling and Pinouts (DB-9 Adapter)
Console
RJ-45-to-RJ-45
Port
Rollover Cable
RJ-45
Signal
RTS
DTR
2
TxD
3
GND
4
GND
5
GND
6
DSR
7
CTS
¹Pin 1 is connected internally to Pin 8.
DB-25 Adapter (for Connecting to a Terminal)
Use the RJ-45-to-RJ-45 rollover cable and the RJ-45-to-DB-25 female DTE adapter (labeled
"Terminal") to connect the console port to a terminal.
asynchronous serial console port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-25
female DTE adapter.
Table I-2: Port Mode 1: Console Port Signaling and Pinouts (DB-25 Adapter)
http://www.cisco.com/warp/public/473/9.html (16 of 19) [9/4/2003 12:36:03 PM]
Pinouts.
RJ-45-to-DB-9
RJ-45
Pin
Pin
8
8
7
6
6
2
5
5
4
5
3
3
2
4
1
7
Console
Terminal
Device
Adapter
DB-9 Pin
Signal
CTS
DSR
RxD
GND
GND
TxD
DTR
RTS
Table I-2
lists the pinouts for the
Console
Table I-1