Cisco Aironet 1400 Series Lembar Spesifikasi - Halaman 11
Jelajahi secara online atau unduh pdf Lembar Spesifikasi untuk Perangkat Keras Jaringan Cisco Aironet 1400 Series. Cisco Aironet 1400 Series 16 halaman. Wireless bridge
Juga untuk Cisco Aironet 1400 Series: Manual (35 halaman)
Halaman Cetak
OSPF Sham-Link Support for MPLS VPN
To create a sham-link, use the following commands starting in EXEC mode:
Command
Step 1
Router1# configure terminal
Step 2
Router1(config)# interface loopback
interface-number
Step 3
Router1(config-if)# ip vrf forwarding
vrf-name
Step 4
Router1(config-if)# ip address ip-address
mask
Step 5
Router1(config-if)# end
Step 6
Router1(config)# end
Step 7
Router2# configure terminal
Step 8
Router2(config)# interface loopback
interface-number
Step 9
Router2(config-if)# ip vrf forwarding
vrf-name
Step 10
Router2(config-if)# ip address ip-address
mask
Step 11
Router2(config-if)# end
Step 12
Router1(config)# end
Step 13
Router1(config)# router ospf process-id
vrf vrf-name
Step 14
Router1(config-if)# area area-id
sham-link source-address
destination-address cost number
Step 15
Router2(config)# router ospf process-id
vrf vrf-name
Step 16
Router2(config-if)# area area-id
sham-link source-address
destination-address cost number
Verifying Sham-Link Creation
To verify that the sham-link was successfully created and is operational, use the show ip ospf
sham-links command in EXEC mode:
Router1# show ip ospf sham-links
Sham Link OSPF_SL0 to address 10.2.1.2 is up
Area 1 source address 10.2.1.1
Run as demand circuit
DoNotAge LSA allowed. Cost of using 40 State POINT_TO_POINT,
Purpose
Enters global configuration mode on the first PE router.
Creates a loopback interface to be used as an endpoint of the
sham-link on PE-1 and enters interface configuration mode.
Associates the loopback interface with a VRF. Removes the IP
address.
Reconfigures the IP address of the loopback interface on PE-1.
Returns to global configuration mode.
Returns to EXEC mode.
Enters global configuration mode on the second PE router.
Creates a loopback interface to be used as the endpoint of the
sham-link on PE-2 and enters interface configuration mode.
Associates the second loopback interface with a VRF. Removes
the IP address.
Reconfigures the IP address of the loopback interface on PE-2.
Returns to global configuration mode.
Returns to EXEC mode.
Configures the specified OSPF process with the VRF associated
with the sham-link interface on PE-1 and enters interface
configuration mode.
Configures the sham-link on the PE-1 interface within a specified
OSPF area and with the loopback interfaces specified by the IP
addresses as endpoints. cost number configures the OSPF cost for
sending an IP packet on the PE-1 sham-link interface.
Configures the specified OSPF process with the VRF associated
with the sham-link interface on PE-2 and enters interface
configuration mode.
Configures the sham-link on the PE-2 interface within a specified
OSPF area and with the loopback interfaces specified by the IP
addresses as endpoints. cost number configures the OSPF cost for
sending an IP packet on the PE-2 sham-link interface.
Configuration Tasks
Cisco IOS Release 12.2(8)T
11