Digitool Solutions TAU-2503 Panduan Pengguna

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Alat Ukur Digitool Solutions TAU-2503. Digitool Solutions TAU-2503 2 halaman. Usb torque & angle meter

Halaman Cetak

Specifications:

Model

Range

Square Drive

TAU-252

2.5-25.00 ft-lb

3/8 inch

TAU-502

5-50.00 ft-lb

3/8 inch

TAU-1002

10-100.0 ft-lb

3/8 inch

TAU-1503

10-150.0 ft-lb

1/2 inch

TAU-2503

25-250.0 ft-lb

1/2 inch

Display

5-digit, alpha-numeric LCD with function and

battery indicator icons.

Accuracy

: Torque: Within ±1% of Indicated Value of both CW

and CCW directions. (10%-100% of F.S)

Angle: Within ± 1° when rotating to 90° at the

speed rate @ 2°/s to 400°/s

Required minimum 5% of F.S pre-torque

Resolution:

Model

Drive

ft-lb

TAU-252

3/8 inch

0.02 ft-lb

TAU-502

3/8 inch

0.05 ft-lb

TAU-1002

3/8 inch

0.1 ft-lb

TAU-1503

1/2 inch

0.2 ft-lb

TAU-2503

1/2 inch

0.3 ft-lb

Units of measure

ft-lb, in-lb, Nm

Modes of measure:

Torque, Angle

Measurement Modes:

ANGLE- Displays applied torque and angle for 15 seconds.

TORQUE - Displays torque value in real time when torque is

loading and shows peak torque when torque is re-

leased.

Visual, Audible Alerts:

Yellow

LED and buzzer pulse at 80% - 96% of target torque. Pulse

rate increases as target torque is being approached.

Green

LED and buzzer alerts continuously when applied torque is

within 96% - 104% of target torque.

Red

LED and buzzer on continuously when applied torque

exceeds >104% target torque or wrench full-scale.

Tactile Vibration when applied torque is within ±4% tolerance of the

target.

Temperature Drift:

±0.0015%/F

Storage Temperature

0ºF to 125ºF

Operating Temperature

40ºF to 110ºF

Humidity -

up to 90% non-condensing

Battery Power:

Uses 3 AAA batteries up to 200 hours of operation

Weight

Certification:

0.6 pound

This device is calibrated at the factory and is certified to meet

0.6 pound

International Standards. ISO-6789-2003 and ASME B107-28-

0.6 pound

2005 standards compliant. Certificate of N.I.S.T. (National

0.8 pound

Institute of Standards Technology). Traceability from 10% to

0.8 pound

100% of full scale

Maintenance:

To clean the meter, wipe with a lightly dampened cloth. DO NOT

use: solvents, thinners or engine cleaners. DO NOT immerse in

any liquids. It is highly recommended that your Torque & Angle

Meter be calibrated once a year or every 15,000 cycles;

whichever comes first. Contact Digitool Solutions representatives

for repair and calibration services.

Warranty Service and Recalibration

in-lb

Digitool Solutions provides a 1 year warranty that covers any

0.2 in-lb

0.05 Nm

Digital Torque & Angle Meter which fails to give satisfactory

service due to defective workmanship or materials (excluding

0.5 in-lb

0.1 Nm

calibration) for 12 months from the date of original purchase.

Calibration is only covered by this warranty for each new unused

0.2 in-lb

0.2 Nm

Torque & Angle Meter out of box. Products must be returned with

proof of purchase—freight prepaid—to the warranty service cen-

0.3 in-lb

0.3 Nm

ter listed below.

0.6 in-lb

0.6 Nm

This warranty excludes Torque & Angle Meters which have been

subjected to abnormal use, accidental damage, neglect, or lack of

maintenance. Any modification or disassembly of this Torque &

Angle Meter, or repair by an unauthorized service center will void

the warranty. This warranty gives you specific rights. You may

also have other rights which vary from state to state. The

foregoing obligation is Digitool Solutions sole liability under this or

any implied warranty; and under no circumstances shall Digitool

Solutions be liable for any incidental or consequential damages.

Note: Some states do not allow the exclusion or limitation of

incidental or consequential damages so the above limitation or

exclusion may not apply to you.

Unit included:

1– TAU-XXXX

2— 3 AAA battery

3— Micro USB Cable

4— Driver software communication from TAU-XXX to PC

(DTS_USB.EXE)

5— Blow mold case

6— User's manual

For Warranty Service and Recalibration/Certification

Services, contact:

Digitool Solutions LLC,.

13905 Ramona Ave. Unit #A

Chino, CA 91710

Phone: (909)591-9581

Fax (909) 233-6491

USER'S GUIDE

USB TORQUE & ANGLE

Meter

For Models

TAU-252, TAU-502, TAU-1002,

TAU-1503 , TAU-2503

Accuracy:

Torque. ±1% CW & CCW of 10%-100% of Full scale

Angle. ±1° of 90° rotation @ speed rate 2°/s - 400°/s

Data record:

Up to 360 Data recorded Torque and Angle values

Battery:

Up to 200 hours operation

Display:

5-digit, alpha-numeric LCD with function

and battery indicator icons.

Power off:

Auto shut off after 2 minutes idle

Ver. Aug 15