Acuity AEL VALIANT Series Petunjuk Instalasi - Halaman 2

Jelajahi secara online atau unduh pdf Petunjuk Instalasi untuk Perlengkapan Lampu Acuity AEL VALIANT Series. Acuity AEL VALIANT Series 2 halaman. Post top led version

Halaman Cetak

VALIANT

MOUNTING:

NOTE: THIS UNIT WILL ACCEPT POLE TOPS WITH AN

EXTERIOR DIAMETER BETWEEN 2.375" AND 3"

1. WHEN PLACING THE UNIT ON THE POLE, FEED THE

SUPPLY LEADS THROUGH THE BASE OF THE UNIT.

NOTE: IF UNIT IS PRE-WIRED, INSTEAD OF STEP 1, FEED

THE SUPPLIED PRE-WIRE THROUGH THE POST TOP AND

DOWN THE POLE.

3. ORIENT THE UNIT SO THE CLOSURE SCREWS (OR

TRIGGER LATCHES IF EQUIPPED) ARE TO THE

STREET SIDE.

4. TIGHTEN THE THREE MOUNTING SET SCREWS.

DO NOT TIGHTEN SET SCREWS

CAUTION

BEYOND 15 ft-lb. TORQUE.

L ADDER REST INSTALLATION:

ADDER REST INSTALLATION:

THE LADDER REST IS FOR

COSMETIC PURPOSES ONLY. IT

CAUTION

IS NOT INTENDED FOR USE AS

AN ACTUAL REST FOR A LADDER.

NOTE: IT IS DESIGNED TO BREAK-AWAY UNDER SIDE FORCE.

HOWEVER, IT CAN BE REATTACHED WITH A 1/4-20X3/4 BOLT

AND NUT AVAILABLE IN THE LADDER REST REPLACEMENT KIT

(THE KIT ALSO CONTAINS TWO ADDITIONAL LADDER RESTS.)

NOTE: THE LADDER REST IS A PRESS FIT DESIGN INTENDED

FOR INSTALLATION AFTER THE UNIT IS INSTALLED ONTO THE

POST TOP.

1. INSERT THE PIN FEATURE ON THE LADDER REST (SEE

FIGURE 3) INTO THE LADDER REST HOLE LOCATED ON

THE LEFT AND RIGHT SIDE OF THE LOWER HOUSING JUST

ABOVE THE MOUNT SET SCREWS.

2. USING A RUBBER MALLET OR HAMMER, GENTLY KNOCK

THE LADDER REST INTO THE HOLE. BE SURE TO KEEP

THE LADDER REST LINED UP WITH THE HOLE SO THAT

THERE SI NO DAMAGE TO THE PIN.

NOTES: IF THE PIN IS DAMAGED BEYOND REPAIR, REMOVE

IT WITH PLIERS AND REATTACH USING A 1/4-20X3/4 BOLT

AND NUT.

GENTLY KNOCK HERE

DRAWING NO. A68128 REV A

American Electric Lighting a division of Acuity Lighting Group, Inc. Granville, OH

INSTALLATION INSTRUCTIONS

SERIES POST TOP LED VERSION cont.

FOR INSTALLATION.

FIGURE 3

LADDER REST INSTALLATION

(BACK)

PHOTOCONTROL:

NOTE: ON THE AVP, NO TOOLING IS NECESSARY FOR THE

PHOTOCONTROL INSTALLATION OR ADJUSTMENT.

- IF NO PHOTOCONTROL OPTION WAS SELECTED, A CUSTOMER

SUPPLIED PHOTOCONTROL WILL NEED TO BE INSTALLED. SEE

STEP 1 BELOW.

- IF "PC" WAS SPECIFIED WHEN ORDERING, THE UNIT WILL COME

WITH THE PHOTOCONTROL INSTALLED. SEE STEP 4 BELOW.

- IF "NR" WAS SPECIFIED, THE UNIT COMES STANDARD WITH A

SHORTING CAP AND THE STEPS BELOW ARE NOT NECESSARY.

1. REMOVE THE CUPOLA CAP BY GRABBING ONE SIDE OF IT AND

LIFTING UP. (SEE FIGURE 1) THE CUPOLA CAP IS VERY RIGID

AND TIGHT, DESIGNED SO IT DOESN'T EASILY COME OFF.

HOWEVER, IT MAY BE REMOVED BY HAND.

2. INSERT THE PHOTOCONTROL INTO THE RECEPTACLE.

3. REATTACH THE CUPOLA CAP. IT SHOULD REATTACH WITH A

VERY AUDIBLE SNAP.

4. TURN THE PHOTOCONTROL WINDOW TOWARD NORTH BY

GRABBING THE CUPOLA BASE WITH BOTH HANDS, LIFTING AND

TURNING SIMULTANEOUSLY UNTIL THE CUPOLA WINDOW IS

FACING NORTH. THE CUPOLA BASE AND THE PHOTOCONTROL

RECEPTACLE ARE KEYED SO THE PHOTOCONTROL TURNS AS

THE CUPOLA DOES.

NOTE: FOR ELECTRICAL SAFETY PURPOSES, THE CUPOLA IS

DESIGNED SO THAT IT WILL NOT TURN BEYOND 360 DEGREES.

DEPENDING ON THE INITIAL ORIENTATION, IT MAY BE NECESS-

ARY TO TURN THE CUPOLA IN THE OTHER DIRECTION IF IT

STOPS AND REFUSES TO TURN.

WIRING:

NOTE: THIS PROCEDURE IS NOT NECESSARY IF UNIT IS

OTE: THIS PROCEDURE IS NOT NECESSARY IF UNIT IS

SUPPLIED WITH PRE-WIRE.

1. OPEN THE HOOD. (SEE "OPENING AND CLOSING THE

UNIT" SECTION.)

2. LOCATE THE WIRING DIAGRAM ATTACHED TO THE

INSIDE OF THE BASE.

3. USING THE WIRING DIAGRAM AS A GUIDE, CONNECT

THE POWER SUPPLY LEADS TO THE TERMINAL BLOCK.

4. CONNECT THE GREEN OR BARE GROUND SUPPLY WIRE

TO THE CASTING BY HOOKING IT AROUND THE HEAD OF

THE GREEN GROUNDING SCREW, LOCATED BESIDE THE

TERMINAL BLOCK, AND TIGHTENING THE SCREW

SECURELY.

5. CLOSE THE UNIT.

PART NUMBER 057-71-68128