Cisco ASR 9000 Series Manual - Halaman 28

Jelajahi secara online atau unduh pdf Manual untuk Gerbang Cisco ASR 9000 Series. Cisco ASR 9000 Series 44 halaman. Line card
Juga untuk Cisco ASR 9000 Series: Mengkonfigurasi Pengaturan Jaringan (26 halaman), Panduan Konfigurasi (46 halaman), Panduan Konfigurasi (50 halaman), Manual (24 halaman), Mengkonfigurasi (46 halaman), Panduan Referensi Cepat (7 halaman)

Cisco ASR 9000 Series Manual
Migrating from RP1 to RP2 Card
• The router must be running Cisco IOS XR software release 5.3.2 or later version.
• The router must have two RP1 cards (active and standby) up and running.
• Cisco ASR 9000 Ethernet Line Card (first generation) must be removed from the chassis as they are
incompatible with RP2.
• Cisco ASR 9000 High Density 100GE Ethernet line cards must be power down or temporarily removed
before starting the migration procedure. Use the hw-module power disable location node-id command
in admin-config mode to power down the LC.
Procedure
Step 1
Use the show redundancy summary command to verify that the RP0 and RP1 are in Ready State.
Example:
Router# show redundancy summary
Wed Jun 17 11:18:51.391 PST
Active/Primary Standby/Backup
-------------- --------------
0/RP0/CPU0(A)
0/RP0/CPU0(P)
Router# show redundancy
Wed Jun 17 11:20:19.086 PST
Redundancy information for node 0/RP1/CPU0:
==========================================
Node 0/RP1/CPU0 is in ACTIVE role
Node Redundancy Partner (0/RP0/CPU0) is in STANDBY role
Standby node in 0/RP0/CPU0 is ready
Standby node in 0/RP0/CPU0 is NSR-ready
Node 0/RP1/CPU0 is in process group PRIMARY role
Process Redundancy Partner (0/RP0/CPU0) is in BACKUP role
Backup node in 0/RP0/CPU0 is ready
Backup node in 0/RP0/CPU0 is NSR-ready
Group
---------
v6-routing
mcast-routing
netmgmt
v4-routing
central-services
dlrsc
dsc
Active node reload "Cause: Initiating switch-over."
Standby node reload "Cause: Initiating switch-over."
Step 2
Remove the standby RP1 card and insert RP2. Follow the procedure explained in the topic
Replacing Cards from the Chassis, on page
Step 3
Connect to RP2 console port and type CTRL+C to break into ROMMON.
Step 4
From the ROMMON prompt of RP2, set ROMMON variable to activate 1GE mode for peer RP communication:
Example:
Replacing Cisco ASR 9000 Series Router Components
28
0/RP1/CPU0(S) (Node Ready, NSR: Ready)
0/RP1/CPU0(B) (Proc Group Ready, NSR: Ready)
Primary
Backup
---------
--------- ---------
0/RP1/CPU0
0/RP0/CPU0
0/RP1/CPU0
0/RP0/CPU0
0/RP1/CPU0
0/RP0/CPU0
0/RP1/CPU0
0/RP0/CPU0
0/RP1/CPU0
0/RP0/CPU0
0/RP1/CPU0
0/RP0/CPU0
0/RP1/CPU0
0/RP0/CPU0
25.
Replacing Cisco ASR 9000 Series Router Components
Status
Ready
Ready
Ready
Ready
Ready
Ready
Ready
Removing and