Epson 1280 - Stylus Photo Color Inkjet Printer Panduan Petunjuk Instalasi - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Aksesori Printer Epson 1280 - Stylus Photo Color Inkjet Printer. Epson 1280 - Stylus Photo Color Inkjet Printer 8 halaman. Product support bulletin(s)
Juga untuk Epson 1280 - Stylus Photo Color Inkjet Printer: Penggantian Kartrid (2 halaman), Buletin Dukungan Produk (6 halaman), Buletin Dukungan Produk (1 halaman), Panduan Tambahan (1 halaman), Panduan Pengguna (27 halaman), Panduan Kompatibilitas (1 halaman), Panduan Tambahan (2 halaman), Mulai di sini (2 halaman), Brosur & Spesifikasi (2 halaman), Informasi Produk (13 halaman), Mulai dari Sini Manual (6 halaman), Spesifikasi (2 halaman), Panduan Pengguna (12 halaman), Buletin Dukungan Produk (3 halaman), Buletin Dukungan Produk (2 halaman), Buletin Dukungan Produk (4 halaman), Buletin Dukungan Produk (7 halaman), Panduan Memulai (32 halaman)

Halaman Cetak
Epson 1280 - Stylus Photo Color Inkjet Printer Panduan Petunjuk Instalasi
Black Felt Marker
•
Small thin screwdriver, not phillips.
•
Scissors
•
Alcohol or Alcohol swabs
•
Pen or Pencil
•
Get everything together in one place so you can do this all at the same time. It will take
about 15 minutes of your time. It is not difficult if you have the right tools. Of course the
second time you do it, it will be a lot easier.
Validate Your Printer Performance and Set Up USB Cable:
1. Before you begin installing the CFS, make sure your printer is working perfectly. If
you don't do this and you have problems later on, you will never know if it is the CFS
or your printer. So, DO NOT SKIP THIS STEP.
Use your Epson cartridges, and check your nozzle pattern, if it looks good, then
print 5 copies of the PURGE6.TIF image (found on the disk provided or our web
site.) The prints must not have any banding or skipping on them. Make sure you
print using 360 DPI, PLAIN PAPER settings. If either the purge6 prints or your
nozzle pattern tests have problems, then run cleaning cycles in groups of 3. Print a
copy of purge6 after 3 cleanings. Always check your nozzles before and after each
cleaning. If you cannot get a perfect print or nozzle pattern, then DO NOT
PROCEED WITH THE INSTALLATION OF YOUR CFS.
Remove Cartridge Hold Down Clamps:
2. Remove the cartridge clamps next. Remove both the black clamp and the color
clamp. With the power on and with the printer idle, push the Orange button under
the printer lid. The cartridges will slide to the left, to the cartridge removal
position. Remove both of the cartridges. Then, use your flat screwdriver to remove
the clamps that were holding the cartridges in place. Put the screwdriver blade in
between the blue and black plastic parts where the clamps are hinged, and twist.
The clamps will pop right off. With the cartridges in the left position, pull the
power cord for the printer out of the wall, disconnecting the printer power.
"At this point, disconnect the printer power by pulling the plug out of the wall"
Install the CFS Cartridges:
3. With the power disconnected, remove the old cartridges and insert the new CFS
color cartridges. There should be 4 felt pads on each cartridge. You may have to
guide these felt pads into the cartridge holder, it is a tight fit. Push the cartridge
all the way down, so the poppet valves are actuated and the contacts touch the
S a v e
M o n e y
MIS Associates Inc
http://www.inksupply.com
a n d
I m p r o v e
2901 Auburn Rd
Fax: 248-289-6013
Y o u r
Auburn Hills, MI 48326
P r i n t i n g
800-445-8296