EPSON Stylus Photo 2000P
Control Panel
paper out light
color ink
out light
black ink
out light
cleaning button
Follow these guidelines when you check the control panel
lights.
P is on
The P power light is on when the printer is on and
ready to print. It flashes when the printer is
receiving a print job, charging ink, or cleaning the
print head.
S flashes
When the S paper out light flashes, you have a
paper jam. Press the E load/eject button to try to
clear the jam. If that doesn't work, turn off the
printer and gently pull out all the paper. Make sure
none of the sheets are curled, creased, old, stuck
together, or too thin. Then reload the paper against
the right edge guide and slide the left edge guide
against it. Turn on the printer and press the
E load/eject button to resume printing. If you're
using roll paper, see page 7 for additional loading
instructions.
S is on
When the S paper out light comes on, your paper
is out or incorrectly loaded. Make sure none of the
sheets are curled, creased, old, stuck together, or
too thin. Then reload the paper against the right
edge guide and slide the left edge guide against it.
Press the E load/eject button to resume printing. If
you're using roll paper, see page 7 for additional
loading instructions.
B or A flash
When an ink out light flashes, your ink supply is
low. Make sure you have a replacement cartridge.
B or A are on
When an ink out light comes on, you need to
replace the ink cartridge. Make sure you have a
replacement cartridge. See page 8 for instructions.
If an ink out light comes on after you've replaced a
cartridge, you installed a cartridge your printer
can't use. Remove it and replace it with the
correct type (see page 1 for ink cartridge
specifications).
P and S flash
When the P power and S paper out lights flash
and
and one or both of the ink out lights come on,
B and A are on
jammed paper may be blocking movement of the
print head. Turn off the printer, open the cover,
and check inside for any jammed paper. Then turn
the printer back on. If the lights still flash and/or
come on, contact your dealer or EPSON.
4 - EPSON Stylus Photo 2000P
power
light
power
button
load/eject button
When all the lights flash, your printer may have an
P S B A
flash
internal error. Make sure you removed all the
packing material as described on the Start Here
poster in your printer box. Then turn off the printer,
wait a few seconds, and turn it on again. If the
lights still flash, contact your dealer or EPSON.
When all the lights are off, the printer is not
P S B A
are off
receiving power. Try these solutions:
Make sure the printer is turned on.
Turn off the printer, plug in the power cord
securely, and turn on the printer again.
Make sure the outlet is operable and is not
controlled by a switch or timer. If in doubt, try
using another outlet.
Installing an Ink Cartridge for the
First Time
Follow these ink cartridge precautions and the others in
"Safety Instructions" in the Printer Basics book:
Install both ink cartridges, and leave them installed for
all types of printing, or the printer won't work.
Remove the yellow tape seal from the top of the ink
cartridges or you'll permanently damage them. Don't
remove the clear seals on the bottom or ink will leak
out.
Don't touch the green chip on the back of the
cartridge. This may inhibit normal operation and
printing.
Never turn off the printer when the
flashing, unless the printer hasn't moved or made any
noise for more than five minutes.
Keep ink cartridges out of the reach of children and
do not drink the ink.
If ink gets on your skin, wash the area thoroughly with
soap and water. If ink gets in your eyes, flush them
immediately with water.
Before you begin, make sure the printer is plugged into an
electrical outlet and turned on.
1. Lower the output tray and open the cover.
6/00
P
power light is
yellow ink cartridge
replacement button
Halaman Cetak