Epson C094001 - FX 870 B/W Dot-matrix Printer Spesifikasi - Halaman 10
Jelajahi secara online atau unduh pdf Spesifikasi untuk Aksesori Printer Epson C094001 - FX 870 B/W Dot-matrix Printer. Epson C094001 - FX 870 B/W Dot-matrix Printer 12 halaman. Hi-capacity cut-sheet feeder
Juga untuk Epson C094001 - FX 870 B/W Dot-matrix Printer: Panduan Perakitan (8 halaman)
Halaman Cetak
FX-870/1170
Data Dump Mode
In data dump mode, the printer produces a printout of all the
codes it receives. To use data dump
1. Make sure the printer is
PAUSE
2. Hold down the
3. Load the paper.
4. Next, run an application program or a program you have
written in any programming language. Your printer prints
all the codes it receives in hexadecimal format and text, as
shown below.
5. To turn off data dump mode, press the
stop printing and then turn off the printer.
By reading the characters printed in the text field on the right
side of the printout or the printout of hex codes, you can
check which codes are being sent to the printer.
In the text field, characters appear as their true
characters if they are printable. Nonprintable codes, such as
control codes, are represented by dots.
Application Software
Most application programs allow you to specify the type of
printer you use so that the program can take full advantage
of the printer's features. Many of these programs provide an
installation or setup section that presents a list of printers.
Choosing from a menu
To take full advantage of your printer's features, choose your
printer when you set up your program. If your printer is not
listed, choose from the following list (the printers are listed in
the order of preference):
FX-870 FX-1170
FX-850 FX-1050
EX-800 EX-1000
FX-86e FX-286e
FX-80+ FX-l00+
FX-80 FX-100
Epson printer
9-pin printer
If you plan to use the IBM printer emulation mode, choose
IBM Proprinter (X for narrow carriage or XL for wide
carriage), IBM Graphics printer, or IBM printer, in that order
of preference.
FX-870/1170-10
follow these steps:
mode,
button while you
PAUSE
button to
To use all the features of your printer, it is best to choose a
program that lists one of the FX printers on its menu. If your
program does not list one of these printers, contact the
software manufacturer to see if an update is available.
Using Continuous Paper
You can load continuous paper through the front, rear, or
bottom paper slots, depending upon the position of the
tractor unit and the placement of your paper supply.
Your printer can handle continuous paper up to 254
(10.0 inches) wide
406 mm (16.0 inches) wide on the wide carriage.
To print on continuous paper, you can install the tractor unit
in one of the following positions: front, rear, or pull. Be sure
you set the paper-release lever correctly before you print.
Tractor position and available paper paths
Below are the possible ways of feeding continuous paper.
the paper-release lever to the position indicated
Always set
for the paper-feed method you want to use.
Tractor
Paper-release
lever position
Front push-
Rear push-
tractor
Pull-tractor
Single-sheet position
For all single sheets, whether loaded from the top or
single sheets from the front with the optional frunt sheet
Front push-tractor position
For continuous paper with the tractor unit installed in
the front.
Rear push-tractor position
For continuous paper with the tractor unit installed in
the rear.
Pull-tractor position
For continuous paper with the tractor unit installed on
the top. In this case, you can load paper from the front,
rear, or bottom.
10/13/92
the standard-width carriage and up to
on
Paper paths
mm
9-Pin Printers