TomTom Go 730 Panduan Pengguna - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk GPS TomTom Go 730. TomTom Go 730 19 halaman. Tomtom go 730: supplementary guide
Juga untuk TomTom Go 730: Manual (2 halaman), Instal Manual (1 halaman), Panduan Pengguna (38 halaman), Panduan Tambahan (1 halaman), Pemasangan poster (2 halaman)

TomTom Go 730 Panduan Pengguna

1. Getting Started

1.1 Unpacking

Unpack your TomTom GO box and identify the
contents. You should have:
• (1) TomTom GO itself. Its main features are a
touch-sensitive LCD screen, a power (On/Off)
button, a release button (for removing TomTom
GO from its cradle) and a Secure Digital (SD)
memory card slot.
• A (2) carry case, for storing TomTom GO when it's
not in your vehicle.
• An (3) AC adapter, included for you to charge and
work with TomTom GO even when it's not in your
vehicle. Note that this comes with several inter-
national pin adapters, for use anywhere in the
world. When you use the adaptor, please make
sure it is cooled by placing it in a ventilated area.
• An (4) SD card, containing map data.
• An (5) installation poster, showing how to
assemble the cradle, how to fix it to your wind-
screen and how to insert TomTom GO.
• An (6) installation CD, containing PC connection
software and extra maps.
• The component parts of a suction-mount (7/8)
cradle, for attaching to your windscreen.
• A (9) DC power lead, with 12V cigarette lighter
adapter. This is the normal way of providing
power to TomTom GO when it's in your vehicle.
• A (10) USB data cable for connecting TomTom GO
to a Windows PC.
• This (11) manual.
• A (12) registration card. You can use it to register
your unit or, if you prefer, enter the same infor-
mation online at www.tomtom.com
Touchscreen
SD card slot
Eject button
On/Off button
Speaker
AC-connector
USB-connector
Docking connector
Do not expose TomTom GO to high temperatures.
We recommend that you do not leave TomTom GO
in direct sunlight for long periods or in an
unattended car on sunny days. High temperatures
can cause permanent damage.
Do not attempt to service TomTom GO yourself! Do
not open, puncture or disassemble it. Doing so may
be dangerous and will invalidate your warranty.

1.2 Assembly

To get started, assemble the suction-mount cradle
as shown in the installation poster. Place the cradle
in a suitable location on your windscreen or side
window and push the black plastic lever away
from you, fixing the cradle in position.
Note that some newer vehicles may have a heat
reflective shield embedded in the windscreen. In
some cases this can prevent proper GPS signal
reception. If this turns out to be a problem in your
vehicle, you will need to purchase and install the
TomTom active antenna kit.
You don't have to use the cradle if you don't want
to. If necessary, TomTom GO can be positioned on
its own anywhere that's convenient, provided that
it's safely secured.
3
Under normal journey conditions, the suction mount
is perfectly sufficient to hold the cradle in position.
Note that suction may be lost if left overnight, due
to condensation and low temperature. For this
reason, and for security, we recommend removing
both the suction mount cradle and TomTom GO
when leaving your vehicle overnight.
To remove the cradle, pull the suction mount lever
towards you. If the cradle still doesn't detach from
your windscreen, tug gently on the clear plastic
tab at the edge of the suction mount, to break the
vacuum seal.
Plug the small plug end of the DC power lead into
the socket on the back of the cradle. Plug the
other end into your vehicle's 12V (cigarette lighter)
socket.
To activate your 12V socket, you may need to use
your ignition key in an 'Accessories' position.
Please consult your vehicle handbook.
Note that TomTom GO contains its own internal
rechargeable battery. For short journeys it may
be possible to do without the DC power lead for
simpler and tidier operation.
Ease TomTom Go onto its cradle by locating its
front edge first and then rotating back firmly until
you hear a click. You'll feel TomTom GO lock into
place. The green LED on TomTom GO's front panel
will light up if the cradle is also connected to your
vehicle's 12V socket.
To adjust the angle of TomTom GO, slacken the
three adjustable knobs on the cradle and then turn
it gently. In addition to tilting the cradle up and
down and from side to side, you can also rotate
TomTom GO in the cradle, from left to right, ±45°.
When you're happy, tighten up the three knobs
again.
After using TomTom GO, remove it from the cradle
by pressing the release button while rotating the
unit forward gently. Put it in the supplied bag. If
you want to clean it, use a soft, dry cloth. Do not
use water or a solvent.