Crow MRX-220N Petunjuk Instalasi - Halaman 2

Jelajahi secara online atau unduh pdf Petunjuk Instalasi untuk Sensor Keamanan Crow MRX-220N. Crow MRX-220N 2 halaman.

Halaman Cetak

FIG.4 - PCB LAYOUT

BLOCK

CONNECTOR

ANTENNA

DOPPLER

ALARM

LED

ROTARY

Tamper

SWITCH

Double Dual Pyrosensors on opposite side

BRACKET SCREW

Install part 1 to wall using 4 screws; connect part 2

to part 1, adjust the detector to required direction

and tighten the bracket screw

TEST PROCEDURES

Wait one-minute for warm-up time after applying

power.

Make the test at the protected area free of moving

people

LED should be in enable position.

Walk test

1. Start walking slowly across the detection zone.

2. Observe that the red LED lights whenever

motion is detected.

3. Allow 5 sec. between each test for the detector

to stabilize.

NOTE:

Walk tests should be done at least once a year to

confirm proper operation of the detector.

You must reset the detector from

Control Panel before the new

settings will take effect

CROW ELECTRONIC ENGINEERING LTD. ("Crow") –

WARRANTY POLICY CERTIFICATE

This Warranty Certificate is given in favor of the purchaser (hereunder the

"Purchaser") purchasing the products directly from Crow or from its authorized

distributor.

Crow warrants these products to be free from defects in materials and

workmanship under normal use and service for a period of 24 months from the

last day of the week and year whose numbers are printed on the printed circuit

board inside these products (hereunder the "Warranty Period").

Subject to the provisions of this Warranty Certificate, during the Warranty

Period, Crow undertakes, at its sole discretion and subject to Crow's

procedures, as such procedures are form time to time, to repair or replace, free

of charge for materials and/or labor, products proved to be defective in

materials or workmanship under normal use and service. Repaired products

shall be warranted for the remainder of the original Warranty Period.

All transportation costs and in-transit risk of loss or damage related, directly or

indirectly, to products returned to Crow for repair or replacement shall be borne

solely by the Purchaser.

Crow's warranty under this Warranty Certificate does not cover products that is

defective (or shall become defective) due to: (a) alteration of the products (or

any part thereof) by anyone other than Crow; (b) accident, abuse, negligence,

or improper maintenance; (c) failure caused by a product which Crow did not

provide; (d) failure caused by software or hardware which Crow did not provide;

(e) use or storage other than in accordance with Crow's specified operating and

storage instructions.

There are no warranties, expressed or implied, of merchantability or fitness of

the products for a particular purpose or otherwise, which extend beyond the

description on the face hereof.

7101296_F

FIG. 5 - OPTIONAL HOLES

LED

Mode

Jumper

PIR

LED LED

A. Wire access holes

B. Use for flat wall mounting or for

mounting with the help of bracket

FIG. 7 - BRACKET MOUNTING AND ASSEMBLY

TECHNICAL SPECIFICATIONS

Detection Method

DOUBLE DUAL element PIR & MW

Maximum ripple

2.4Vdc peak to peak at 12Vdc

Power Input

8.2 to 16 Vdc

Current Draw

Start-up: 28mA + 3mA

Standby: 23mA + 3mA

Active :

Temperature

Compensation

YES

Alarm Period

1.8 sec

Alarm Output

N.C 28Vdc 0.1 A with 10 Ohm

series protection resistors

N.O 28Vdc 0.1 A with 10 Ohm

series protection resistors

Tamper Switch

N.C 28Vdc 0.1A with 10 Ohm series

Protection resistor - open when

cover is removed

Warm Up Period

60 sec

This limited Warranty Certificate is the Purchaser's sole and exclusive remedy

against Crow and Crow's sole and exclusive liability toward the Purchaser in

connection with the products, including without limitation - for defects or

malfunctions of the products. This Warranty Certificate replaces all other

warranties and liabilities, whether oral, written, (non-mandatory) statutory,

contractual, in tort or otherwise.

In no case shall Crow be liable to anyone for any consequential or incidental

damages (inclusive of loss of profit, and whether occasioned by negligence of

the Crow or any third party on its behalf) for breach of this or any other

warranty, expressed or implied, or upon any other basis of liability whatsoever.

Crow does not represent that these products can not be compromised or

circumvented; that these products will prevent any person injury or property

loss or damage by burglary, robbery, fire or otherwise; or that these products

will in all cases provide adequate warning or protection.

Purchaser understands that a properly installed and maintained product may in

some cases reduce the risk of burglary, fire, robbery or other events occurring

without providing an alarm, but it is not insurance or a guarantee that such will

not occur or that there will be no personal injury or property loss or damage as

a result.

Consequently, Crow shall have no liability for any personal injury; property

damage or any other loss based on claim that these products failed to give any

warning.

If Crow is held liable, whether directly or indirectly, for any loss or damage with

regards to these products, regardless of cause or origin, Crow's maximum

liability shall not in any case exceed the purchase price of these products,

which shall be the complete and exclusive remedy against Crow.

FIG. 6 - WA PIR + MW DETECTION

TECHNICAL SPECIFICATIONS (CONT.)

Operating Temperature

RFI Protection

EMI Protection

Visible Light Protection

20mA + 3mA

MW center frequency

Dimensions

Weight

ISRAEL:

USA:

AUSTRALIA:

POLAND:

LATIN AMERICA:

ITALY:

These instructions supersede all previous issues in circulation prior to July 2005.

PATTERN

Assembled view

-20°C to +50°C(-4°F to +122°F)

30V/m 10 - 1000MHz

50,000V of electrical

interference from lightning or

power through

stable against halogen light

2.4 m (8ft ) or reflected light

X-Band: 9.9 GHz

10.525 GHz

10.687 GHz

154mm x 114mm x 74mm

(6.1" x 4.5" x 2.9")

290gr. (10.23oz)

CROW reserves the rights to change

specifications without prior notice

CROW ELECTRONIC ENGINEERING LTD.

Crow Electronic Engineering Ltd.

12 Kineret St. Airport City, 70100

PO. Box 293 Ben Gurion Airport

Tel: 972-3-9726000

Fax: 972-3-9726001

E-mail:

[email protected]

2160 North Central Road,

Fort Lee, N.J. 07024

Tel: 1-800-GET CROW

(201) 944 0005

Fax: (201) 944 1199

E-mail:

[email protected]

429 Nepean HWY Brighton East Vic 3187

Tel: 61-3-9596 7222

Fax: 61-3-9596 0888

E-mail:

[email protected]

VIDICON SP. ZO. O.

15 Povazkowska St.

01 – 797 Warsaw Poland

Tel: 48 22 562 3000

Fax: 48 22 562 3030

E-mail:

[email protected]

CROW LATIN AMERICA

5753 NW 151

.Street

MIAMI LAKES,

FL 33014 – USA

Tel: +1-305-823-8700

Fax: +1-305-823-8711

E-mail:

[email protected]

DEATRONIC

VIA Giulianello 4/14

00178 ROMA, ITALY

Tel: +39-0676-12912

Fax: +39-0676-12601

E-mail:

[email protected]