Epson Stylus Color 740 Panduan Informasi Produk - Halaman 15

Jelajahi secara online atau unduh pdf Panduan Informasi Produk untuk Aksesori Printer Epson Stylus Color 740. Epson Stylus Color 740 17 halaman. Product support bulletin(s)
Juga untuk Epson Stylus Color 740: Lembar Informasi Produk (4 halaman), Brosur (2 halaman), Lembar Informasi Produk (4 halaman), Buletin Dukungan Produk (6 halaman), Buletin Dukungan Produk (1 halaman), Panduan Pengguna (24 halaman), Panduan Instalasi Perangkat Lunak (8 halaman), Spesifikasi (2 halaman), Petunjuk Penyiapan Cepat (5 halaman), Buletin Dukungan Produk (3 halaman), Buletin Dukungan Produk (2 halaman), Buletin Dukungan Produk (4 halaman), Buletin Dukungan Produk (7 halaman), Panduan Online (10 halaman)

Halaman Cetak

Epson Stylus Color 740 Panduan Informasi Produk

Each staggered horizontal and straight vertical line should be

complete, with no gaps in the dot pattern. If your printout

looks okay, you're done. If any dots are missing, as shown

below, clean the print head again; see "Cleaning the Print

Head" on page 14 for instructions.

Aligning the Print Head

If your printouts contain misaligned vertical lines, you may

need to align the print head using the Print Head Alignment

utility in your printer software. Your printer must be

connected to a local port, not on a network, to use this utility.

Follow these steps:

1. Make sure the printer is turned on and paper is loaded.

Caution:

Load paper that's at least 8.27 inches (210 mm) wide.

This prevents ink from spraying inside the printer and

smudging your printouts.

For the best results, load EPSON ink jet paper in the

printer whenever you check the print head alignment.

2. Start an application and open a document.

3. Access the printer settings dialog box as described in the

Printer Basics book.

4. Click the

tab (Windows) or the

Utility

(Macintosh). You see the Utility menu.

5. Click the

Print Head Alignment

6. Follow the instructions on the screen to print a test page

and select the correct alignment.

Cleaning the Printer

To keep your printer working at its best, you should clean it

several times a year, following these steps:

1. Turn off the printer, unplug the power cord, and

disconnect the printer cable.

2. Remove all the paper from the sheet feeder.

3. Clean the exterior of the printer with a soft, damp cloth.

4. Clean ink out of the printer's interior with a soft, damp

cloth.

Missing dots

Utility icon

icon.

Caution:

Don't touch the gears inside the printer.

Never use alcohol or thinner for cleaning; they can

damage the printer components and case.

Don't use a hard or abrasive brush.

Don't get water on the printer components.

Don't spray lubricants or oils inside the printer.

Transporting the Printer

If you move your printer some distance, you need to prepare it

for transportation in its original box. Follow these steps:

1. Turn on the printer and wait until the print head locks in

the far right position. Then turn off the printer.

Caution:

To avoid damage, always leave the ink cartridges

installed when transporting the printer.

2. Unplug the power cord from the electrical outlet. Then

disconnect the interface cable from the printer.

3. Remove any paper from the printer and remove the paper

support.

4. Push in the output tray extensions and close the tray.

5. Repack the printer and attachments in the original box

using the protective materials that came with it. See the

Unpacking Sheet that was packed with your printer.

Be sure to keep the printer level as you transport it. If you

notice a decline in print quality after transporting the printer,

clean the print head (see "Cleaning the Print Head" on

page 14); if output is misaligned, align the print head (see

"Aligning the Print Head" on page 15).

Epson Stylus Color 740 Panduan Informasi Produk - Halaman 15

Aligning the Print Head

Cleaning the Printer

Transporting the Printer

Related Documentation