Motorola APX NEXT Panduan Instalasi

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Radio Dua Arah Motorola APX NEXT. Motorola APX NEXT 2 halaman. Vehicle charger
Juga untuk Motorola APX NEXT: Panduan Memulai Cepat (29 halaman)

Halaman Cetak

APX NEXT Vehicle Charger

PMPN4640 Installation Guide

*MN009444A01*

MN009444A01-AB

MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M

logo are trademarks or registered trademarks of Motorola Trademark

Holdings, LLC and are used under license. All other trademarks are the

property of their respective owners.

Printed in

blasting area, or in areas posted "Turn off two-way

radio." Obey all signs and instructions.

OPERATIONAL CAUTIONS

EFFICIENT SYSTEM OPERATION

•

All equipment must be properly grounded according to

Motorola Solutions installation instructions for safe

operation.

•

All equipment should be serviced only by an authorized

technician.

INSTALLING THE VEHICLE CHARGER

Mounting hardware supplied includes a trunnion bracket for

mounting the unit below the vehicle dashboard, on the floor,

or on the wall, and a cable for connection to the electrical

system of the vehicle. The bracket enables the charger to be

pivoted to a position that offers the best security to the

portable radio during rough driving conditions.

The vehicle charger is designed for 12 V or 24

V, negative ground system.

Plan the location for mounting the charger. Identify the

routing paths for the cable and verify that the cable

length is adequate. Also check the mounting penetra-

tions required. On most vehicles, it is necessary to pen-

etrate the firewall to reach the battery. Check the

opposite side of the firewall for cable clearance before

drilling holes. Protect the cable where it passes through

the firewall by use of appropriate rubber grommets (not

supplied) or other protective measures.

Survey the firewall for existing holes occupied by vehicle wire

harnesses. Often there is an opportunity to route other cables

using the same path. Because of the wide variation in vehicle

design, these instructions may be modified to suit each

particular installation:

•

DO consider a mounting location which will allow the unit

to be mounted at a

•

45-degree up angle. This angle provides operational

convenience and physical security for the portable radio

under rough traveling conditions.

•

DO use heat shrink tubing on all splices.

•

DO ensure that the cable is not placed under stress, is

not exposed to weather, and is not subjected to damage

due to engine heat.

•

DO retain the in-line cable fuse when trimming the cable

to fit. Locate the in-line fuse as close as practical to the

supply voltage connection.

•

DO check the opposite sides of all mounting surfaces

before drilling, to insure that there are no obstructions,

such as vehicle wiring and fluid lines.

•

DO NOT attach the unit to any part of the vehicle that is

not rigid or is subject to excessive vibration.

•

DO NOT install the unit in an area where rain or snow can

easily get into it, such as next to a vehicle window which

may be left open.

•

DO NOT install the unit in a location where it could

interfere with the operator or operating controls of the

vehicle.

•

DO NOT dress the cable over sharp edges that could

cause wear or tearing of cable insulation.

SAFETY AND GENERAL INFORMATION

•All batteries can cause property damage

or bodily injury, or both, such as burns if a

conductive material such as jewelry, keys,

or beaded chains touches exposed

W A R N I N G

terminals. The material may complete an

electrical circuit (short circuit) and become quite hot.

Exercise care in handling any charged battery, particularly

when placing it inside a pocket, purse or other con tainer

with metal objects.

•

Do not replace or charge batteries in potentially explosive

atmosphere. Contact sparking can occur while installing

or removing batteries and cause an explosion.

•

Due to the risk of electrical shock or other physical injury,

never insert your hands into the charger pocket.

PRODUCT SAFETY AND RF EXPOSURE

COMPLIANCE

Before using this product, read the Product

Safety and RF Exposure booklet enclosed with

your radio which contains important operating

instructions for safe usage and RF energy

awareness and control for Compliance with

applicable Standards and Regulations.

•

DO NOT install the unit in a location where it may be

difficult for the operator to reach.

•

DO NOT install the unit where it may interfere with the

vehicle safety air bag deployment.

•

DO NOT install the unit where the LED indicators and

switch may become physically damaged.

Using the trunnion bracket as a template, mark the

mounting surface drilling locations. It is recommended

that at least four screws be used, with 1/4 in. being the

preferred fastener diameter.

Re-verify that there are no wires, fluid lines, or other

obstructions on the other side of the mounting location,

and drill appropriate sized holes for the mounting screws

to be used.

Referring to Figure 1, mount the bracket using appropri-

ate screws, washers, lock washers, and nuts.

OPERATIONAL WARNINGS

VEHICLES WITH AN AIR BAG

•Do not place a portable radio or install

radio communications equipment in the

area over an air bag or in the air bag

deployment area. Air bags inflate with

W A R N I N G

great force. If a portable radio is placed

in the air bag deployment area and the air bag inflates,

the radio may be propelled with great force and cause

serious injury to occupants of the vehicle.

•

Installation of vehicle communication equipment should

be performed by a professional installer/technician

qualified in the requirements for such installations. The

size of an airbag, shape, and deployment area can vary

by vehicle make, model, and front compartment

configuration (for example, bench seat as opposed to

bucket seats).

•

Contact the corporate headquarters of the manufacturer

of the vehicle, if necessary, for specific airbag

information for the vehicle make, model, and front

compartment configuration involved in your

communication equipment installation.

BLASTING CAPS AND AREAS

•To avoid possible interference with

blasting operations, turn your radio off

and remove it from the charger when

you are near electrical blasting caps, in a

W A R N I N G

Figure 1 Installing the Vehicle Charger

Insert the unit into the bracket, and install the washer

and threaded knob into the housing, as shown in Figure