ABB Dodge HSCXT305A Petunjuk Manual

Jelajahi secara online atau unduh pdf Petunjuk Manual untuk Penggerak DC ABB Dodge HSCXT305A. ABB Dodge HSCXT305A 16 halaman. Screw conveyor and hydroil screw conveyor drive

Halaman Cetak

Dodge

Screw Conveyor and Hydroil Screw Conveyor Drive

SCXT105 thru SCXT705 Single Reduction Screw Conveyor Drive

HSCXT105 thru HSCXT505A Single Reduction Hydroil Screw Conveyor Drive

These instructions must be read thoroughly before installation or operation. This instruction manual was accurate at the time of

printing. Please see baldor.com for updated instruction manuals.

Note! The manufacturer of these products, Baldor Electric Company, became ABB Motors and Mechanical Inc. on

March 1, 2018. Nameplates, Declaration of Conformity and other collateral material may contain the company name of

Baldor Electric Company and the brand names of Baldor-Dodge and Baldor-Reliance until such time as all materials have

been updated to reflect our new corporate identity.

WARNING: To ensure the drive is not unexpectedly

started, turn off and lock-out or tag power source before

proceeding. Failure to observe these precautions could

result in bodily injury.

WARNING: All products over 25 kg (55 lbs) are noted on the

shipping package. Proper lifting practices are required for

these products.

NOTE: A Screw Conveyor Drive consists of two

subassemblies and drive shaft listed below.

Reducer – Includes speed reducer, shaft retainer,

retainer bolt and lockwasher.

Adapter Assembly – Includes adapter bolts,

lockwashers, a lip type seal, a seal retaining ring and

drive shaft key.

Make certain none of the parts have been damaged in

shipment. Any shipping damage should be promptly

reported to the carrier. Read all instructions in this

manual before attempting to assemble or install the

Screw Conveyor Drive. It is important that assembly

be performed in the following sequence and that each

step be completed before continuing to the next.

WARNING: Because of the possible danger to person(s) or

property from accidents which may result from the improper

use of products, it is important that correct procedures be

followed. Products must be used in accordance with the

engineering information specified in the catalog. Proper

installation, maintenance and operation procedures must

be observed. The instructions in the instruction manuals

must be followed. Inspections should be made as necessary

to assure safe operation under prevailing conditions. Proper

guards and other suitable safety devices or procedures as

may be desirable or as may be specified in safety codes

should be provided, and are neither provided by ABB nor

are the responsibility of ABB. This unit and its associated

equipment must be installed, adjusted and maintained by

qualified personnel who are familiar with the construction

and operation of all equipment in the system and the

potential hazards involved. When risk to persons or property

may be involved, a holding device must be an integral part

of the driven equipment beyond the speed reducer output

shaft.

NOTE: This reducer is compatible with the ABB Ability

Smart Sensor that can be installed in the adapter plug

labeled "smart sensor". The plug and sensor can be moved

to different locations as required by mounting position.

Place reducer on blocks so that it lays flat with the

input shaft down.

Position adapter on reducer output hub so that small

end (end with 12 holes) rests on reducer. Select the 4

mounting holes to match the shaft used (Figure 1).

Place adapter screws and lockwashers through

adapter and thread into reducer. Do not tighten.

Place seal in adapter so that spring faces out. Seal

should be tapped evenly into place in the adapter

with a soft hammer, applying force only on the outer

corner of the seal. Fill cavity between lips of seal

with grease. Install seal retainer ring by tapping with

a hammer. Apply grease to adapter section of shaft

(middle section). Slide shaft, keyseated end first, into

adapter and through reducer.

NOTE: Be extremely careful when sliding adapter

section of shaft through seal to prevent seal lips from

being damaged or rolled over.

Carefully place reducer on its side. Rotate shaft to

align keyseats in shaft and output hub and install key.

Install shaft retainer, lockwasher and bolt. Tighten

bolt to torque specified in Table 4.

Lay reducer on blocks with input shaft down and

tighten adapter bolts to torque specified in Table 4.

If waste packing is to be used, it may be installed

through access hole provided in the adapter. Waste

packing, not furnished with the screw conveyor

drive, may be used as a separate seal option or in

combination with the lip seal.

ASSEMBLY