ARGSeguridad ZDAS-300 Panduan Pengguna - Halaman 16

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Sistem Keamanan ARGSeguridad ZDAS-300. ARGSeguridad ZDAS-300 16 halaman. Luxury voiced lcd alarm system

Halaman Cetak

System config

SET

The first auto disarmed Auto disarmed

The first auto disarmed：press * or # to select the 1--6

Figure12: The first auto disarmed time is at 17:35.

3.10 The Phone Numbers Setting

How To Set Phone Number: Press the PROG key on the Keypad, a series of - - - will

appear on the LCD. Press the Disarm key on any current registered Key Fob or entering the

preprogrammed PIN code, and the word 'Sensor' will appear on the LCD. Pressing the * key

on the Keypad, the LCD will show the words 'Zone type'. Pressing the # key on the Keypad,

the LCD will show the words 'SYS phone'. Press No 1 on the numeric Keypad. Enter the full

phone number of the Central Station Comms.and press PROG to store this number. Pressing

* then # scroll back down to 'SYS phone' Press No2 on the numeric Keypad. Enter the full

phone number of the Central Station secondary number for comms using the numeric keypad

on the panel, then Press PROG to store this number. The No 1 and 2 are for C.S. Phone

numbers, No 3 to 6 are for personal numbers. If not networking, No 1 and 2 can also be set

with personal numbers.

If no further actions take place the panel will automatically return to normal state after

approximately 30 seconds. Otherwise at the end, press the Dis-Arm key on a registered Key

Fob to return the panel to normal state.

3.11 The C.S. Account Code Setting

How To Set C. S. Code: Press the PROG key on the numeric Keypad, a series of - - - will

appear on the LCD.

Auto disarmed time

CONFIG

TIMED

Press disarming key on any current registered key fob or entering the preprogrammed

PIN code, and the word 'Sensor' will appear on the LCD. Pressing the * key on the Keypad,

the LCD will show the words 'Zone type'. Pressing the # key on the Keypad, the LCD will

show the words 'SYS phone'. Press No 7 key on the keypad, the Panel will access the

location of the C.S. account code. Enter the account code using the numeric keypad on the

panel, this is normally a 4 Digit Code called site code. Press 'Prog' key to store the

programmed number.

If no further actions take place the panel will automatically return to normal state after

approximately 30 seconds. Otherwise at the end, press the Dis-Arm key on a registered Key

Fob to return the panel to normal state.

3.12 Deleting Zones

How To Delete a Zone: There are two ways to delete a zone

A: Delete all the detectors within the zone.

Press the DELETE key on the keypad, , a series of - - - will appear on the LCD. Press

the Disarm key on any current registered Key Fob or entering the preprogrammed PIN code

and the word 'DEL Sensor' will appear on the LCD. Pressing the 0 then 1 key on the Keypad

to select the Zone number of the detector or Key fob that needs to be deleted. e.g. select 3 on

Keypad, the LCD will display 'Zone 3'. Using the numeric Keypad select the number of the

detector requiring to be deleted. e.g. Detector No 4 in Zone 3. The LCD will now display

'Zone 3 4'. Press DELETE and the detector will be deleted from memory.

B: Enter the location of zone type setting, set the No 7 field to 0, refer to 3.8 figure 10.

3.13 Viewing The Recording Event Log

Events refer to occurrences taking place within your s ystem, such as, which key Fob

Armed or Dis-Armed the system and when. If an alarm occurred which detector in which

Zone activated the alarm and when.

How To View the event record: press the * key on the keypad, the panel LCD will show

the latest event, using the * and # keys to look over previous events, times and information.

Note: the top line always shows the latest event information.

Figure13: The LCD display when there is a panic alarm from the keypad

LOG

RMOT

ALM

: remote panic alarm

ALM