Motorola GM Series Informasi Layanan - Halaman 21

Jelajahi secara online atau unduh pdf Informasi Layanan untuk Radio Motorola GM Series. Motorola GM Series 34 halaman. Professional radio
Juga untuk Motorola GM Series: Panduan Servis (28 halaman), Panduan Instalasi (36 halaman)

Halaman Cetak

VHF (136-174MHz) Transmitter Power Amplifier (PA) 45 W

5.6

Antenna Switch

The antenna switch consists of two PIN diodes, D3471 and D3472. In the receive mode, both diodes

are off. Signals applied at the antenna jack J3401 are routed, via the harmonic ﬁlter, through

network L3472, C3474 and C3475, to the receiver input. In the transmit mode, K9V1 turns on Q3471

which enables current sink Q3472, set to 96 mA by R3473 and VR3471. This completes a DC path

from PASUPVLTG, through L3473, D3471, L3477, L3472, D3472, L3471, R3474 and the current

sink, to ground. Both diodes are forward biased into conduction. The transmitter RF from the

directional coupler is routed via D3471 to the harmonic ﬁlter and antenna jack. D3472 also

conducts, shunting RF power and preventing it from reaching the receiver port (RXIN). L3472 is

selected to appear as a broadband lambda/4 wave transmission line, making the short circuit

presented by D3472 appear as an open circuit at the junction of D3472 and the receiver path.

5.7

Harmonic Filter

Components L3491-L3494 and C3489-C3498 form a nine-pole Chebychev low-pass ﬁlter to

attenuate harmonic energy of the transmitter to speciﬁcations level. R3490 is used to drain

electrostatic charge that might otherwise build up on the antenna. The harmonic ﬁlter also prevents

high level RF signals above the receiver passband from reaching the receiver circuits, improving

spurious response rejection.

5.8

Power Control

The transmitter uses the Power Control IC (PCIC, U3501) to control the power output of the radio. A

portion of the forward and reﬂected RF power from the transmitter is sampled by the directional

coupler, rectiﬁed and summed, to provide a DC voltage to the RFIN port of the PCIC (pin 1) which is

proportional to the sampled RF power.

The ASFIC contains a digital to analog converter (DAC) which provides a reference voltage of the

control loop to the PCIC via R3517. The reference voltage level is programmable through the SPI line

of the PCIC. This reference voltage is proportional to the desired power setting of the transmitter, and

is factory programmed at several points across the frequency range of the transmitter to offset

frequency response variations of the transmitter's power detector circuitry.

The PCIC provides a DC output voltage at pin 4 (INT) which is ampliﬁed and shifted in DC level by

stages Q3501 and Q3502. The 0 to 4 volt DC range at pin 4 of U3501 is translated to a 0 to 8.5 volt

DC range at the output of Q3501, and applied as VCONT to the power-adjust input pin of the ﬁrst

transmitter stage U3401. This adjusts the transmitter power output to the intended value. Variations

in forward or reﬂected transmitter power cause the DC voltage at pin 1 to change, and the PCIC

adjusts the control voltage above or below its nominal value to raise or lower output power.

Capacitors C3502-4, in conjunction with resistors and integrators within the PCIC, control the

transmitter power-rise (key-up) and power-decay (de-key) characteristic to minimize splatter into

adjacent channels.

U3502 is a temperature-sensing device, which monitors the circuit board temperature in the vicinity

of the transmitter driver and ﬁnal devices, and provides a dc voltage to the PCIC (TEMP, pin 29)

proportional to temperature. If the DC voltage produced exceeds the set threshold in the PCIC, the

transmitter output power will be reduced so as to reduce the transmitter temperature.

2-11