Epson ChromaBlast 1.0 Panduan Pemilik - Halaman 7
Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Perangkat lunak Epson ChromaBlast 1.0. Epson ChromaBlast 1.0 13 halaman. For epson stylus pro 4880
Juga untuk Epson ChromaBlast 1.0: Panduan Memulai (47 halaman)
Halaman Cetak
❏ If you're using Windows,
the function key that lets you display on an external
monitor. It may have an icon such as
labelled
. (Allow a few seconds for the projector to
CRT/LCD
sync up after pressing it.)
The remote control doesn't work
❏ Make sure you've removed the battery insulating tape. See
the Quick Setup sheet for instructions.
❏ Make sure you're within 20 feet of the projector.
❏ Point the remote control at one of the projector's two
infrared receivers. You should be within range of the infrared
receivers (about 30° left or right, and 15° above or below).
❏ You may need to replace the remote control's battery. See
page 9 for details.
❏ Dim the room lights and turn off any fluorescent lights.
Make sure the projector is not in direct sunlight.
❏ Remove the clear film covering the infrared receivers.
❏ Turn off nearby equipment that emits infrared energy, such
as a radiant room heater.
Only part of the picture is displayed, or
the picture is distorted.
❏ Press the
button to select a different aspect ratio.
Aspect
❏ If the image is distorted or contains interference, make sure
the cable is securely connected at both ends.
❏ If the image looks like
buttons on the projector's control panel.
The picture is upside-down or reversed.
Change the
option in the setting menu.
Projection
The picture is blurry
❏ There may be dirt on the lens. Clean the lens with a canister
of compressed air or lens-cleaning paper. If necessary,
moisten a soft cloth with lens cleaner and gently wipe the
lens surface. Never rub the lens with abrasive materials.
❏ Adjust the focus ring.
❏ Adjust the
Sharpness
❏ If you're projecting from a computer, press the
on the remote control to automatically optimize the image.
The colors on the screen don't look right
❏ Press the
button on the remote control to move
Color Mode
through the different color mode settings.
❏ If the picture looks too dark, you may need to replace the
lamp. See page 10 for details.
®
hold down the
key and press
Fn
, or it may be
or
, press the
setting on the Image menu.
Auto
❏ You may be using the wrong source setting. Press the
Source
S-Video/Video
through the source settings.
❏ Adjust the following settings in the projector's Image menu
under
Picture Quality
(video only),
Flesh Tone
The picture contains static or noise.
❏ Make sure your cable is securely connected at both ends.
❏ Don't use an extension cable or a cable longer than 6 feet.
❏ If you're displaying the same image on your computer and
projector screen, try turning off your laptop's LCD display.
The projector and notebook don't display
the same image
If you're using Windows:
❏ On most systems, the
toggle between the LCD screen and the projector, or display
on both at the same time.
❏ You might need to use the Display utility in the Control
Panel to enable both the LCD screen and external monitor
port. Check your notebook's manual or online help.
❏ If you have dual monitor support, you may need to uncheck
the option to extend your Windows desktop in the Display
Properties.
and
If you're using Mac OS
1. Select
System Preferences
click
Displays
2. Click
Detect Displays
button
3. To display the entire desktop on both your projector screen
and LCD screen, click the
(If you don't see this tab, make sure it isn't hidden by
another window on your screen.)
7/03
EPSON PowerLite Home 10 Projector
button on the projector, or the
buttons on the remote control to move
:
Brightness
(video only),
Tint
Color Temperature
.
or
CRT/LCD
®
X:
from the Apple
.
.
Arrangement
EPSON PowerLite Home 10 Projector - 7
or
Input A/B
,
,
Contrast
Saturation
, and
key lets you
®
menu and
Click here
or
tab.
Arrange