Toshiba 38TVDA028 Panduan Pemilik - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Pendingin Udara Toshiba 38TVDA028. Toshiba 38TVDA028 12 halaman.

Halaman Cetak
INDOOR UNIT DISPLAY
1
1
2
1 TIMER (White)
2 OPERATION (White)
● Display brightness can be adjusted, follow procedure on !.
PREPARATION BEFORE USE
2
Preparing Filters
1. Open the air inlet grille and remove the air filters.
2. Attach the filters. (see detail in the installation manual).
Loading Batteries (when use wireless operation.)
1. Remove the slide cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Remote Control Reset
1. Remove the batteries.
2. Press .
3. Insert the batteries.
AIR FLOW DIRECTION
3
Press :
Move the louver in
1
the desired vertical direction.
2
Press :
Swing the air
automatically and press again to stop.
For horizontal direction, adjust
3
manually.
Note:
● Do not move the louver manually by others.
● The louver may automation positioning by some operation mode.
REMOTE CONTROL
4
1 Infrared signal emitter
2 Start/Stop button
3 Mode select button (
)
4 Temperature button (
)
5 Fan speed button (
)
6 Swing louver button (
)
7 Set louver button (
)
8 Off timer button (
)
9 High power button (
)
0 Economy button (
)
! Clear button (CLEAR)
@ Check button (CHECK)
AUTOMATIC OPERATION
5
To automatically select cooling or fan only operation
1. Press
: Select Auto A.
2. Press
: Set the desired temperature. Min. 17°C, Max. 30°C
3. Press
: Select AUTO, LOW , LOW+
MED+
, or HIGH
1
3
2
7
9
8
@
, MED
,
.
COOLING / FAN ONLY OPERATION
6
1. Press
2. Press
Fan Only: No temperature indication
3. Press
MED+
, or HIGH
DRY OPERATION
7
For dehumidification, a moderate cooling performance is controlled
automatically.
1. Press
2. Press
Note: Dry mode fan speed is set to Auto only.
Hi POWER OPERATION
8
To automatically control room temperature and airflow for faster cooling
(except in DRY and FAN ONLY mode)
Press
: Start and stop the operation.
ECO OPERATION
9
To automatically control room temperature to save energy (except in DRY and
FAN ONLY mode)
Press
: Start and stop the operation.
Note: Cooling operation; the set temperature will increase automatically
1 degree/ hour for 2 hours (maximum 2 degrees increase).
TIMER OPERATION
10
Set the timer when the air conditioner is operating.
1
Press
2
Press
3
Press
4
Press
DISPLAY LAMP BRIGHTNESS ADJUSTMENT
11
To decrease the display lamp brightness or turn it off.
1. Press and hold
4
or
) is shown on remote control LCD then release the button.
2. Press
6
Rise
5
0
Remote control
!
LCD
Lamp illuminates full brightness.
Lamp illuminates 50% brightness.
Lamp illuminates 50% brightness and the
operation lamp is turned off.
All lamps are turned off.
● In the examples of
going off.
: Select Cool
or Fan only
: Set the desired temperature. Min. 17°C, Max. 30°C
: Select AUTO, LOW , LOW+
, MED
.
: Select Dry
.
: Set the desired temperature. Min. 17°C, Max. 30°C
Setting the OFF timer
for enter OFF timer setting.
for select desired OFF timer. (0.5 - 12 hrs)
for set OFF timer.
again for cancel OFF timer.
for 3 seconds until brightness level (
or
to adjust brightness in 4 levels
Decrease
Operation display
and
, the lamp illuminates for 5 seconds before
.
,
,
,
Brightness
100%
50%
50%
All turned off