Toshiba ASYG14LMCB Panduan Pengoperasian - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Pengoperasian untuk Pendingin Udara Toshiba ASYG14LMCB. Toshiba ASYG14LMCB 48 halaman.

Halaman Cetak

Remote Controller Overview and Operations

Remote controller display

In this section, all the possible indicators are displayed for description.

In actual operation, the display is linked with the button operation, and

only shows the necessary indicators for each setting.

POWERFUL button

The product will operate at maximum power, which is convenient

when you want to quickly cool down or warm up the room.

When you press the button to start the POWERFUL operation, the

indoor unit emits 3 short beeps.

POWERFUL operation is automatically turned off in the following

situations:

• Adjusted room temperature reached to the deﬁ ned temperature in

temperature setting in COOL, DRY, or HEAT mode.

• 20 minutes have passed after ﬁ nishing the POWERFUL operation

mode setting.

It is not turned off automatically during setting of the POWERFUL

operation.

Notes:

• The airﬂ ow direction and the fan speed are controlled automatically.

• This operation cannot be performed simultaneously with ECONOMY

operation.

To return to normal operation, press the button again. Then the indoor

unit emits 2 short beeps.

10 °C HEAT button

Starts 10 °C HEAT operation that mainains the room temperature at

10 °C so as to prevent the room temperature to drop too low.

When you press the button to start the 10 °C HEAT operation, the

indoor unit emits 2 short beeps and the ECONOMY indicator (green)

turns on.

Notes:

• In 10 °C HEAT operation mode, only vertical airﬂ ow direction can be

adjusted by using

• HEAT mode will not be performed if the room temperature is warm

enough.

• In multi-type air conditioning system, if other indoor unit is in HEAT

mode, the temperature of the room where 10 °C HEAT operation is

performed will rise. When performing 10 °C HEAT operation, all the

indoor units should be run in 10 °C HEAT operation mode.

To return to normal operation, press the START/STOP button.

The ECONOMY indicator turns off.

Signal transmitter

Aim to signal receiver of the indoor unit properly.

• Signal transmit indicator

that signal from the remote controller is being transmitted.

• Operating range is approximately 7 m.

• You will hear a beep if the transmitted signal has been sent properly.

If there is no beep, press the button on the remote controller again.

FAN button

Controls the fan speed.

(AUTO)

(HIGH)

• When AUTO is selected, the fan speed is automatically adjusted

according to the operation mode.

SWING button

Starts or stops automatic swing of the vertical airﬂ ow direction louver.

• Each time you press the button, the vertical airﬂ ow direction louver

swings as follows:

COOL, DRY, or FAN

6 7

Notes:

• SWING operation may stop temporarily when the fan in the unit is

rotating at very low speed or stopping.

• In FAN mode, either of swing direction 1  3 or 4  7 is performed

in accordance with the vertical airﬂ ow direction previously set before

you start the SWING operation.

OPERATING MANUAL

En-4

9333003061_OM.indb 4

button.

on the remote controller display shows

(MED)

(LOW)

(QUIET)

HEAT or FAN mode

mode

10 SET button

Adjusts the vertical airﬂ ow direction.

11 SLEEP timer button

Activates the SLEEP timer that helps you to fall asleep comfortably

with gradual temperature control.

12 Timer CANCEL button

Cancels the set timer.

13 RESET button

When you press the RESET button, press it gently by using the tip of

a ballpoint pen or other small object in correct direction as shown in

this ﬁ gure.

RESET

14 CLOCK ADJUST button

Cancels the set timer.

15 OFF timer button

Activates the OFF timer.

16 ON timer button

Activates the ON timer.

17 SELECT button

Used for adjusting the clock or timer.

18 OUTDOOR UNIT LOW NOISE button

Starts or stops OUTDOOR UNIT LOW NOISE operation that lowers

noise generated from the outdoor unit by cutting down the rotation

number of the compressor, and suppressing the fan speed till they

are sufﬁ ciently reduced.

Once the operation is set, the operation setting is preserved until you

press this button again to stop the operation, even if the indoor unit

operation is stopped.

OUTDOOR UNIT LOW NOISE indicator

controller display shows that the unit is in OUTDOOR UNIT LOW

NOISE mode.

Notes:

• This operation cannot be performed simultaneously with following

modes:

FAN mode, DRY mode, POWERFUL operation mode

• This operation cannot be performed on a multi-type air conditioner.

If this mode is unintentionally set on a multi-type air conditioner,

cancel the setting by pressing the button. Otherwise, the signal of

the remote controller cannot be transmitted properly.

19 ECONOMY button

Starts or stops ECONOMY operation that saves more electricity

consumption than the other operations with a conservative adjustment

of the room temperature.

When you press the button, the ECONOMY indicator on the indoor

unit turns on.

• In COOL or DRY mode, the room temperature will be adjusted at a

few degree higher than the deﬁ ned temperature.

In HEAT mode, the room temperature will be adjusted at a few

degree lower than the deﬁ ned temperature.

• Especially in COOL or DRY mode, you can have improved

dehumidiﬁ cation without signiﬁ cantly lowering the room temperature.

Notes:

• In COOL, HEAT, or DRY mode, the maximum output of this

operation is approximately 70 % of usual air conditioning operation.

• This operation cannot be performed during temperature monitoring

by AUTO mode.

• In multi-type air conditioning system, ECONOMY operation is

performed only on the indoor unit whose ECONOMY button on the

corresponding remote controller is pressed.

: The setting must be done while the indicator stays solid.

: The button is controllable only when the air conditioner is on.

See page 5

See page 3

See page 5

See page 3

on the remote

20/09/2013 10:10:12