Dimplex BF9000 Panduan Servis - Halaman 10

Jelajahi secara online atau unduh pdf Panduan Servis untuk Perapian Dalam Ruangan Dimplex BF9000. Dimplex BF9000 17 halaman. Dimplex
Juga untuk Dimplex BF9000: Panduan Pemilik (19 halaman), Panduan Pemilik (20 halaman), Panduan Pemecahan Masalah (2 halaman), Panduan Pemilik (19 halaman), Panduan Servis (18 halaman)

Halaman Cetak

the bottom panel.

14. Insert new bulbs.

15. Re-assemble the firebox in reverse order.

NOTE: Ensure the rear tab/ledge on the log-set/ember-

bed is installed tightly under the bottom of the partially

reflective glass to prevent light leakage.

FLICKER MOTOR/FLICKER ROD

REPLACEMENT

Tools Required: Phillips head screw driver

CAUTION: Follow "Preparation for Service" instructions

before proceeding.

1. Slightly wedge your fingers between the back partially

reflective glass and the log-set/ember-bed on either

the right or left side. Pull the back edge of the plastic

ember bed forward until the rear tab/ledge clears past

the bottom of the partially reflective glass and pull the

log set forward and out.

IMPORTANT: Only handle the log-set by the plastic

ember-bed, not the logs themselves.

NOTE: Log-set fits tightly into firebox. Some force

may be necessary to remove.

NOTE: If your model has the media tray with the

decorative glass pieces as an ember bed, remove the glass

pieces then remove the plastic media tray following the

same method as the log set removal instructions.

2. Set log set or media tray aside in a safe location.

3. Disconnect flicker rod from the motor by slightly bend-

ing the flicker rod and pulling the rubber gasket off the

motor shaft. (Figure 3).

NOTE: Be careful not to bend the rod. Doing so may

damage the rod. Ensure the rod is straight after re-instal-

lation so that it doesn't affect the operation of the flicker

effect.

4. Carefully turn the firebox upside down so that the bot-

tom panel is facing up.

5. Remove the 9 screws that attach the bottom panel to

the side panels, (2) on the back side, (2) on the left

side, (2) on the right side and (3) on the bottom along

the front edge.

6. Remove the 3 flicker motor wire ends out of the termi-

nal block by removing the small Philips head screw in

the 3 respective terminals. Take note of their location

on the terminal block.

NOTE: A capacitor is also connected in 2 of the 3

terminals that hold the flicker motor wires on the terminal

block. Take note of the terminal locations and the wire

configuration.

7. Using a Philips screwdriver (a short screwdriver is

recommended), remove the 2 screws holding the flicker

motor to the mounting brackets. One screw on either

side and remove the flicker motor out of the housing.

Take note of the orientation on the brackets.

8. Place the new motor into the housing and attach the

motor to the brackets using the 2 Philips screws.

9. Insert the 3 wire ends from the new flicker motor as

well as the 2 wires from the original capacitor into the

terminal block following the orientation of the original

motor & capacitor. (See Assembly Part Pictures)

10. Tighten terminal screws to secure wires in place.

11. Re-assemble the firebox in reverse order.

NOTE: Ensure the rear tab/ledge on the log-set/em-

ber-bed is installed tightly under the bottom of the partially

reflective glass to prevent light leakage.

HEATER ASSEMBLY REPLACEMENT

Tools Required: Philips head screwdriver

Needle nose pliers

CAUTION: Follow "Preparation for Service" instructions

before proceeding.

1. Remove 9 screws that secure the top panel to the side

panels of the firebox using a Philips head screwdriver,

(2) on the left side; (2) on the right side; (3) on the

backside; (2) on the top.

2. Lift the top off the firebox. Turning the panel 45 de-

grees, rest it inside the cavity at the top to provide you

with some support and leverage while following Steps

4 & 5.

3. Noting their original location, disconnect the wires at-

tached to the end of the heater assembly on the blower

motor and element. Using a flat head screwdriver gen-

tly pry between the end of the connector and the heater

to release the wires

NOTE: Some of the wires may have a "piggy-back"

connector that allows a second wire to connect to the same

prong as the first wire. Keep the "piggy-back" connection

together when pulling the wires off the heater assembly.

4. Remove the 2 mounting brackets that attach the heater

assembly to the top panel. Ensure that the heater as-

sembly is supported when removing the brackets.

5. Remove the mounting brackets from the heater as-

sembly by removing the 2 Philips screws from each

bracket.

6. Attach the brackets to the new heater assembly and

then attach brackets to the top panel.

7. Re-assemble in reverse order as above.

HIGH TEMPERATURE CUTOUT

REPLACEMENT

Tools Required: Philips head screwdriver

Needle nose pliers

CAUTION: Follow "Preparation for Service" instructions

before proceeding.

1. Remove 9 screws that secure the top panel to the side

panels of the firebox using a Philips head screwdriver,

(2) on the left side; (2) on the right side; (3) on the

backside; (2) on the top.

2. Lift the top off the firebox. Turning the panel 45 de-