Epson PowerLite 737c Pengaturan Cepat

Jelajahi secara online atau unduh pdf Pengaturan Cepat untuk Perangkat lunak Epson PowerLite 737c. Epson PowerLite 737c 2 halaman. Release of check tool for network projectors v1.00 for windows
Juga untuk Epson PowerLite 737c: Panduan Pengguna (42 halaman), Panduan Pengoperasian (36 halaman), Panduan Pengaturan Cepat (2 halaman), Panduan Pengoperasian (47 halaman), Daftar Bagian (1 halaman), Buletin Dukungan Produk (30 halaman), Informasi Produk (24 halaman), Panduan Instalasi (19 halaman), Panduan Pengguna (1 halaman), Buletin Dukungan Produk (25 halaman), Buletin Dukungan Produk (38 halaman), Buletin Dukungan Produk (12 halaman), Buletin Dukungan Produk (42 halaman), Buletin Dukungan Produk (22 halaman), Buletin Dukungan Produk (28 halaman), Buletin Dukungan Produk (41 halaman), Buletin Dukungan Produk (34 halaman), Buletin Dukungan Produk (38 halaman), Buletin Dukungan Produk (28 halaman), Buletin Dukungan Produk (15 halaman), Buletin Dukungan Produk (22 halaman)

Halaman Cetak
Epson PowerLite 737c Pengaturan Cepat
EPSON
1
Turn On Your Equipment
1
Connect the power cord to the back of the projector and plug the other
end into an electrical outlet.
2
Remove the lens cover.
3
Remove the battery cover on the remote control. Locate the batteries
that came with the projector and insert them as shown. Then replace
the battery cover.
4
To turn the projector on, press the red
projector or the remote control. The projector beeps once, and the
projector's Power light flashes green and then stays on.
CAUTION: Before unplugging the projector...
Shut the projector down properly:
1. Press the
Power button twice. Let the projector cool while the
Power light flashes orange (about 20 seconds).
2. Once the light stops flashing and the projector beeps, it's safe to
unplug the projector.
2
Adjust the Image
1
To raise the image, press the blue foot release button for the front
adjustable foot and lift the front. Release the button to lock the
foot in position.
PowerLite
737c/ 745c
®
®
Quick Setup
Power button on the
2
Turn the focus ring to sharpen the image.
Turn the zoom ring to reduce or enlarge the image.
Focus
3
If your image looks like
or
to one side of the screen at an angle. Place it directly in front of the
screen, facing the screen squarely.
4
If your image looks like
or
the projector to correct it.
3
Choose a
Presentation Method
How do you want to get images to the projector?
•
To connect to a notebook, see "If connecting
to a notebook" below.
•
To project over an 802.11g/b network, see
"If projecting wirelessly" on the back of this sheet.
You must have installed the projector's EasyMP
software and configured your projector and
computer before you can project wirelessly.
See your User's Guide for instructions.
•
To give a presentation stored on a memory card,
see Chapter 5 in your User's Guide.
If connecting to a notebook...
1
Make sure you've turned on the projector and adjusted the image
as described in sections 1 and 2.
2
Locate the computer cable that came with the projector. Connect
one end to the projector's blue Computer/Component Video port.
Connect the other end to your notebook's video-out port or
monitor port. If you can't connect the cable to your
PowerBook
, you may need to use an adapter. See your
®
PowerLite 737c/745c User's Guide for instructions.
3
Press the Source Search button on the projector until your
computer image is displayed.
Zoom
, you've placed the projector off
, press the
or
buttons on
Computer cable
TM
Wireless card
Turn over