Toshiba 24 WA20 Series Panduan Petunjuk Pengoperasian - Halaman 16
Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk TV Toshiba 24 WA20 Series. Toshiba 24 WA20 Series 47 halaman.
Juga untuk Toshiba 24 WA20 Series: Panduan Memulai Cepat (49 halaman)
Halaman Cetak
DVBS Configuration Setting screen will be displayed
next. First Antenna type(*) should be set. Universal,
Single Cable and Jess Singlecable options are
available. Set the Antenna Type as Universal for
Direct and DiSEqC satellite systems. If you set the
antenna type as Universal, press the Right directional
button to proceed to the next step. If the antenna
type is set as Single Cable or Jess Singlecable,
there will be three more additional options on the
DVBS Configuration Setting screen: Tuner, Band
frequency and User Defined. User Defined option
will be available if the Band frequency is set as User
Defined. Set these options if available and press the
Right directional button to proceed.
(*) This option may be named as Satellite type depending on
the country selection.
Depending on the country and satellite type selections
you made in the earlier steps of the initial setup
process, Load Preset List screen may be displayed
next. Highlight Load Preset List and press OK or the
Right directional button to proceed with the SatcoDX
installation. You can also skip this step by selecting
Skip option.
After the parameters on the DVBS Configuration
Setting screen are configured according to your
environment and preset list installation preference is
selected the next step may be Select Satellite screen.
You may be able to set up different satellites depending
on the selected antenna type and operator in the
previous steps. Highlight the desired satellite option
and press OK to set the parameters(*). The Satellite
Status of the first satellite option will be set as On. In
order to configure other settings of the satellite and to
enable scan this option should be set as On first. Press
Back button and select next satellite you want to set.
After you completed the configuration changes, press
the Right directional button to proceed.
(*) If you have a Direct satellite system, DiSEqC Set option
should be set as DiSEqC A.
If Load Preset List option is selected in the previous
step next steps will be skipped and the preset channel
list installation will start. If the correct satellite has not
been selected for SatcoDX installation, a warning
dialogue will be displayed on the screen. The satellite/s
that can be selected will be listed. Press OK to close
the dialogue and then set the satellite accordingly.
Channel Scan screen will be displayed next. Select
Scan and press OK or the Right directional button
to proceed with the scanning configurations. Select
Skip Scan to proceed without performing a scan and
complete the initial setup.
DVBS Scan Configure screen will be displayed next
if Scan option is selected. Following options will be
available: Scan Mode and Channels. You can choose
to perform a full scan or a network scan. Set the
Scan Mode accordingly. If you are going to perform a
network scan, make sure that you have adjusted the
Frequency, Symbol Rate (Ksym/s) and Polarisation
parameters under the Transponder option accurately
on the Satellite Setup screen. You may not be able
to change the Scan mode setting depending on the
previous selections. If the Channels option is set
as Free encrypted channels will not be installed.
Additional options may also be available depending
on the selected operator, configure these settings
according to your preferences. Once you are done
with setting the available options, press the Right
directional button to start scan while Scan Mode or
Channels is highlighted. While the search continues
you can press the Back button to cancel the search.
The channels that have already been found will be
stored in the channel list.
When the initial setup is completed results will be
displayed. Press OK to finish the setup.
Home Screen will be displayed. You can press the Exit
button on the remote or highlight the Live TV app from
the Apps row on the Home Screen and press OK to
switch to Live TV mode and watch TV channels. For
some countries, the Live TV app will be situated in the
Home tab on the Home Screen and the row with this
app will be named as Favourite Apps.
Initial Setup Wizard
Note: Follow the on-screen instructions to complete the initial
setup process. Use the directional buttons and the OK button
on the remote to select, set, confirm and proceed.
When turned on for the first time, a welcome screen
will be displayed. Select your language and press
OK. Follow the on-screen instructions to setup your
TV and install channels. The installation wizard will
guide you through the setup process. You can perform
initial setup anytime using the Reset option in the
Settings>Device Preferences menu. You can access
the Settings menu from the Home screen or from the
TV options menu in Live TV mode.
1. Welcome Message and Language Selection
"Welcome" message will be displayed along with
the language selection options listed on the screen.
Select the desired language from the list and press
OK to continue.
2. Initial Setup
After the language selection you can start the initial
setup wizard. Highlight Continue and press OK to
proceed. You will not be able go back and change the
language once you proceed. If you need to change
the language after this step you will have to switch
the TV into standby mode so the setup process starts
from the beginning when you next switch on the TV. In
order to do this, press and hold the Standby button. A
dialogue will be displayed. Highlight OK and press OK.
English - 15 -
(**) Limited Models Only