Philips AZ 2045 Manual - Halaman 6

Jelajahi secara online atau unduh pdf Manual untuk Sistem stereo Philips AZ 2045. Philips AZ 2045 8 halaman. Cd soundmachine
Juga untuk Philips AZ 2045: Panduan Pengguna (9 halaman), Panduan Pengguna (15 halaman), Spesifikasi (2 halaman), Panduan Pengguna (12 halaman), Panduan Servis (34 halaman), Manual (10 halaman), (Swedia) Snabbmanual (8 halaman)

Philips AZ 2045 Manual

DIGITAL TUNER

DIGITAL TUNER
Tuning to radio stations
1 Press y to on, then press SOURCE to select
.
TUNER
is displayed briefly and then the radio station
TU
frequency, waveband and, if programmed, a
preset number are shown. (See 4)
2 Press BAND once or more to select your
waveband.
3 Press and hold ∞ or § until the frequency in the
display starts running.
™ The radio automatically tunes to a station of
sufficient reception. Display shows
during automatic tuning.
™ If a FM station is received in stereo,
shown.
4 Repeat steps 2-3 if necessary until you find the
desired station.
• To tune to a weak station, press ∞ or § briefly
and repeatedly until you have found optimal
reception.
To improve radio reception:
• For FM, extend, incline and turn the telescopic
aerial. Reduce its length if the signal is too strong.
• For MW (LW), the set uses a built-in aerial. Direct
this aerial by turning the whole set.
Programming radio stations
You can store up to a total of 30 radio stations in the
memory, manually or automatically (Autostore).
Manual programming
1 Tune to your desired station (see Tuning to radio
stations).
2 Press PROG to activate programming.
3 Press PRESET DOWN/ UP once or more to select
a preset number.
4 Press PROG to confirm.
5 Repeat steps 1-4 to store other stations.
Note: You can erase a preset station by storing
another frequency in its place.
CD PLAYER
Autostore
Autostore automatically starts programming radio
stations from preset 1. Available stations are
programmed in order of waveband reception strength:
FM, followed by MW (LW). Any previous presets e.g.
manually programmed will be erased.
• Press PROG for 4 seconds or more to activate
autostore programming.
™ The display shows
, program blinks,
AUTO
followed by the radio station details when
stored. (See 5)
After all stations are stored, the first autostore preset
station will then automatically play.
To listen to a preset or autostore station
is
Press the PRESET (up or down) buttons once or more
until the desired preset station is displayed.
CD PLAYER
Playing a CD
This CD player plays Audio Discs including
CD-Recordables and CD-Rewritables.
1 Press y to on, then SOURCE to select
if no CD is inserted.
2 Insert a CD with the printed side facing up and
close the CD door.
™ Display: total number of tracks and playing time.
is shown if you have inserted a
non-finalized CD-R(W).
3 Press 2; to start playback.
if your CD contains non-audio
files
4 To pause playback press 2;. Press 2; again to
resume play.
5 To stop CD playback, press 9.
Note: CD play will also stop when:
– the CD door is opened
– the CD has reached the end
– you select tape or tuner source.
CD PLAYER
Selecting a different track
• Press ∞ or § on the set, once or repeatedly to
select.
• In the pause/stop position, press 2; to start
playback.
Finding a passage within a track
1 Press and hold ∞ or §.
™ The CD is played at high speed and low volume.
2 When you recognize the passage you want, release
∞ or § to resume normal playback.
Note: During a CD program or if shuffle/ repeat
active, searching is only possible within a track.
Different play modes: SHUFFLE and REPEAT
You can select and change the various play modes
before or during playback, and combine the modes
with PROGRAM.
shuffle – tracks of the entire CD/ program are
played in random order
shuffle and repeat all – to repeat the entire CD/
programme continuously in random order
repeat all – repeats the entire CD/ program
.
CD
repeat (and shuffle repeat) – plays the current
(random) track continuously
1 To select play mode, press MODE once or more.
2 Press 2; to start playback if in the stop position.
3 To select normal playback, press MODE repeatedly
until the various modes are no longer displayed.
– You can also press 9 to cancel your play mode.

CASSETTE RECORDER

Programming track numbers
In the stop position, select and store your CD tracks in
the desired sequence. Up to 20 tracks can be stored in
the memory.
1 Press ∞ or § on the set to select your desired
track number.
2 Press PROG.
™ If you attempt to programme without first
selecting a track number,
is
shown.
3 Repeat steps 1-2 to select and store all desired
tracks.
™ Display:
if you try to programme more
than 20 tracks.
Reviewing the programme
In the stop position, press and hold PROG until the
display shows all your stored track numbers in
sequence.
Erasing a programme
You can erase the programme by:
• pressing 9 twice
is displayed briefly and
disappears.
• selecting
or
source.
TAPE
TUNER
CASSETTE RECORDER
Cassette playback
1 Press y to on, then SOURCE to select
TAPE
™ Display: shows
throughout tape
operation.
2 Insert a cassette and close the door.
3 Press PLAY 2 to start playback.
4 To pause, press PAUSE ;. Press again to resume.
5 Press SEARCH 5 or 6 to fast wind the tape.
6 To stop the tape, press STOP/OPEN 9/.
• The keys are automatically released at the end of a
tape, except if PAUSE ; has been activated.
.