Toshiba TDP-TW100 Panduan Pemilik - Halaman 23

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Proyektor Toshiba TDP-TW100. Toshiba TDP-TW100 46 halaman. Brochure
Juga untuk Toshiba TDP-TW100: Spesifikasi Produk (2 halaman)

Halaman Cetak
Toshiba TDP-TW100 Panduan Pemilik
Using the menus (Continued)

■ Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.
Item
Description
Projector
Input
Input source name
Mode name
RGB input mode
Resolution
Resolution (in dots)
Frequency
Sync frequency
Sync
Sync signal polarity
Signal format
Y/P
/P
signal format
B
R
Video mode
Color method of video signal
Lamp time
Time of lamp use
Lamp reset count
The count for lamp replacement
Total time
The total time that this projector
is used.
Version
Firmware version
Notes
p.87
1: The mode of supported RGB signals
2: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult
with a dealer about getting replacement for:
TLPLW9 for TDP-TW95 or
TLPLW10 for TDP-TW100
(sold separately).
4: [Version] shows the version of the projector's internal control program. This version is referred
to for customer service, etc.
Note
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
"Yes": displayed, "No": not displayed
Computer Y/P
/P
Video S-video
B
R
Yes
Yes
Yes
Yes
[Note 1]
Yes
No
No
No
Yes
No
No
No
Yes
No
No
No
[Note 2]
Yes
No
No
No
No
Yes
No
No
No
No
Yes
Yes
[Note 3]
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
[Note 4]
Yes
Yes
Yes
Yes
is shown.
44

How to use the USB terminal

The supplied wireless LAN USB adapter allows users to connect the projector to a com-
puter via wireless communication, which supports IEEE802.11b/g wireless LAN
(Toshiba does not guarantee the operation of all computers that are IEEE802.11b/g
compliant.)
This projector can connect with a commercial USB memory and a USB memory card
Wireless/
reader that are USB2.0 compliant, a digital camera or the like and display the JPEG files
USB
saved in those devices.
(Toshiba does not guarantee the operation of all USB 2.0-compliant devices.)
Yes
To connect or disconnect a USB device, use the following procedure:
No
No
■ Connecting USB device
No
No
Plug the USB device.
No
Make sure the orientation is correct then plug the
No
USB device in until it stays securely.
Yes
Yes
Yes
Yes
■ Disconnecting USB device
q Switch the input to Wireless/USB and press the MENU button twice to
display the Setting display (2), then select and run Unplug device in
the Control setting menu.
The processing for disconnecting a USB device starts.
w The message "Safe to remove the USB device" appears on the
screen.
e Unplug the USB device.
Be sure to perform the above operations. Disconnecting a USB device during
operation may cause a malfunction or data corruption.
Notes
• The projector may not recognize a supported USB device. In such a case, unplug
the USB device then re-plug it.
• The USB terminal does not support the supplied mouse remote control receiver or
a commercial mouse controller.
• A USB hub is also not supported.
Precaution
• Disconnecting the power plug while the USB device is operating may cause a
malfunction or data corruption.
p.54
45
.
p.46
USB device