Dimplex AC3CN Panduan Pengguna - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Pemanas Dimplex AC3CN. Dimplex AC3CN 4 halaman. Recessed ceiling heater/ over door heater
Juga untuk Dimplex AC3CN: Petunjuk (4 halaman), Panduan Pengguna (8 halaman)

Halaman Cetak

WARNING

This heater is not equipped with a device to control the

room temperature. Do not use this heater in small rooms when they

are occupied by persons not capacble of leaving the room on their

own, unless constant supervision is provided.

This appliance is not intended for use by persons (inlcuding children)

with reduced physical, sensory or metal capabilities, or lack of

experince and knowledge, unless they have been given supervision

or instruction concerning use of the apppliance by a person

responsible for their safety.

Children should be supervised to ensure that they do not play with

the appliance.

Maintenance

WARNING: ALWAYS DISCONNECT HEATER FROM THE POWER

SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.

Thermal Safety cut-out(s)

The power supply to the heating elements will be interrupted if one or a

combination of the following abnormal events occur:

Air inlet/outlet panel is obstructed.

I n t e r n a l v e n t i l a t i o n i s i m p a i r e d d u e t o b u i l d u p o f d u s t

and ﬂ uff.

Blower unit stalls.

Note : If the cut-out operates, the fan may continue to run impairing the

performance of the heater. The heater must be turned off immediately and

the cut-out(s) reset following the 'Procedure for resetting cut-out(s)'.

DIMPLEX

MILLBROOK HOUSE

GRANGE DRIVE

HEDGE END

SOUTHAMPTON

SO30 2DF

[c] GDC Group Ltd,

A division of GDC Group Ltd,

Procedure for resetting cut-out(s)

Establish cause and eliminate.

You need to reset thermal cut-out(s), located behind the Air Inlet/Outlet panel

(for detail view see Fig. 11).

To reset the thermal safety cut-out, press the black reset button (see 'g' in

Fig. 11) on the side of the cut-out (see 'f' in Fig. 11) as described in steps

2 - 4 :-

Steps to reset cut-out(s)

Disconnect power supply.

Pass small ﬂ at head screwdriver through Air Inlet/Outlet panel 'B' to

button side of cut-out (see 'g' in Fig. 11) avoiding contact with element

(see 'e' in Fig. 11).

Press reset button in direction shown in Fig. 11 to reset cut-out.

(Cut-out clicks when reset)

Remove screwdriver carefully.

Turn on supply.

If the cut-out continues to operate intermittently, the heater should be switched

off and a service agent contacted.

Cleaning of Heater / Switch Panel

External and grille appearance can be maintained by occasionally vacuuming

or wiping with a light duster. External appearance of the Switch Panel can be

maintained by wiping occasionally with a light duster or for stain removal, a

weak soap solution can be applied with a cloth and the surface wiped dry.

Note: Care must be taken to avoid any moisture ingress into the switch

panel.

After Sales Service

Your product is guaranteed for one year from the date of purchase.

Within this period, we undertake to repair or exchange this product free of

charge provided it has been installed and operated in accordance with these

instructions.

Your rights under this guarantee are additional to your statutory rights, which

in turn are not affected by this guarantee.

Should you require after sales information or assistance with this product

please go to www.dimplex.co.uk where you will ﬁ nd our self help guide by

clicking on "After Sales" or ring our helpdesk on 0845 600 5111 (UK) or 01

842 4833 (R.O.I.) .

Spare parts are also available on the website www.dimplex.co.uk

Please retain your receipt as proof of purchase.

TEL: 0845 600 5111

FAX: 01489 773050

WEBSITE: www.dimplex.co.uk

Republic of Ireland

Tel.

01 8424833

Fig. 11