CRU Dataport Data Express DX115 SAS/SATA 6G Panduan Memulai Cepat - Halaman 3
Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Penyimpanan CRU Dataport Data Express DX115 SAS/SATA 6G. CRU Dataport Data Express DX115 SAS/SATA 6G 3 halaman.
Juga untuk CRU Dataport Data Express DX115 SAS/SATA 6G: Panduan Memulai Cepat (2 halaman)
Halaman Cetak
b. I
E
s
nsert the included Data
x pre s
Key into the keylock and turn inn it
secure the carrier to the frame.
c. P ress and hold the Power Button to power the unit on until the Drive Ready LED be g ins to
flash and the hard drive inside be g ins to spin up.
NOTE:
If the drive is already installed in the receiving frame before a system
power up, you do not have to press and hold the s w itch to power on the drive.
When any h a r
d drive is
first used with the Data Port 25 Secure it w]il show up as a blank,
unallocated drive and you'll ne e d to format the dr iv e inside the enclosure before you can use
drive will
Note that formatting a
erase all data on the drive, so
data before beginning this operation.
1.4 Safe Carrier Removal
a. Turn off the computer or properly dismount the drive from the system. Disconnecting the unit
without first u nm ou nti ng the volume can result
Mac Systems
Unmount the volume before powering down the u n it by dra gg ing the
volume's icon to the trash bin, or by selec t ng the volume then pressin(J
Command-E.
Windows Systems
Unmount the DX115 befo r e powering it down by left-clicking the green a rro w icon on the task
bar (in Windows XP) or the USB plug icon with the green checkmark on the Desktop task bar
7, 8),
(Windows Vista,
and then selecting the proper device frorn the rnenu that pops u p. You
S
may have to click on the
ho w Hidden Icons" arrow on the task bar to find the c o rre c t icon.
"
Windows
will indicate when it is safe to disconnect the DataPort 25.
b. Use the DataPort Key to t u r n the keylock 90 degrees counter-clockwise to unlock and power
off the unit
c. Push
the eject button below the keylock once to r elease the button, and again to eject the
,
ca r ri e r.
90
s
degrees c lock w i
e to
it.
be
sure to back up your
in data
ss
lo
.
2 Identifying the Parts of Your DX115 6G
Push Here to Eject Carrier
fiqure 1· Front Bezel
Activity Di�wblro
Fioure 2- DX115 Receiv1ng Frame Rear Panel
3 Other Configuration Options
*Some SATA PC systems/host controllers provide support for t h e
system/host controller manufacturer's documentation
host
in
u
) to
1
connection (cable not
c l
d e d
Pin
locatecJ on Receiving Frarne Motherboard (Figure
v1a
system/host controller manufacturer's docurnentat;on
3.2 Fan Error LED Disable Switch
(
F
1)
This switch
see
i gu re
allows the user to disable the Fan Error LED (insert a paper clip or simili:Jr
)
object to activate switch
CRU-DataPort recommends replacing a faulty tan immediately Contac�
Technical Supportto obtain a new fan.
Drive Ready/Error
LED
Drive Activity LED
Fan Error LED
Disable Switch
Power Sw1tch
SAS/SATA
Power Connector
Connector
Cooling
Fan
Drive
LED
Activity
feature (refer
the SAT/I. !'C
to
for further
Drive
LED
information). The
Activity
be enclbled
can
2).
Refer to the
tor f
r
r
u
t h
Information.
e
SATA
PC
·