Pioneer DEH-4400BT Panduan Pengoperasian - Halaman 18

Jelajahi secara online atau unduh pdf Panduan Pengoperasian untuk Penerima Mobil Pioneer DEH-4400BT. Pioneer DEH-4400BT 30 halaman. Cd rds receiver
Juga untuk Pioneer DEH-4400BT: Panduan Instalasi (33 halaman), Panduan Memulai Cepat (8 halaman)

Halaman Cetak

Pioneer DEH-4400BT Panduan Pengoperasian

Operating this unit

A. ANSR (automatic answering)

1 Press M.C. to turn automatic answering on or off.

R.TONE (ring tone select)

1 Press M.C. to turn the ring tone on or off.

PB INVT (phone book name view)

1 Press M.C. to switch between the lists of names.

Audio adjustments

Press M.C. to display the main menu.

Turn M.C. to change the menu option

and press to select AUDIO.

Turn M.C. to select the audio function.

After selecting, perform the following proce-

dures to set the audio function.

FAD/BAL (fader/balance adjustment)

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between fader (front/rear) and

balance (left/right).

3 Turn M.C. to adjust speaker balance.

! When the rear output and RCA output setting are

SW, you cannot adjust front/rear speaker balance.

Refer to REAR-SP (rear output setting) on the next

page. Refer to PREOUT (preout setting) on the

next page.

PRESET EQ (equalizer recall)

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the equalizer.

DYNAMIC—VOCAL—NATURAL—CUSTOM—

FLAT—POWERFUL

3 Press M.C. to confirm the selection.

TONE CTRL (equalizer adjustment)

! Adjusted equalizer curve settings are stored in

CUSTOM.

1 Press M.C. to display the setting mode.

2 Press M.C. to select BASS (bass)/MID (mid)/TRE-

BLE (treble).

3 Turn M.C. to adjust the level.

Adjustment range: +6 to –6

LOUD (loudness)

Loudness compensates for deficiencies in the low-fre-

quency and high-frequency ranges at low volume.

1 Press M.C. to select the desired setting.

OFF (off)—LOW(low)—HI (high)

SUB.W (subwoofer on/off setting)

This unit is equipped with a subwoofer output which

can be turned on or off.

1 Press M.C. to select the desired setting.

NOR (normal phase)—REV (reverse phase)—OFF

(subwoofer off)

SUB.W CTRL (subwoofer adjustment)

The cut-off frequency and output level can be ad-

justed when the subwoofer output is on.

Only frequencies lower than those in the selected

range are outputted from the subwoofer.

! When you select OFF in SUB.W, you cannot select

this function. For details, refer to SUB.W (subwoo-

fer on/off setting) on this page.

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between the cut-off frequency

and output level of the subwoofer.

Cut-off frequency (Cut-off frequency display

flashes.)—Output level (Output level display

flashes.)

3 Turn M.C. to select the desired setting.

Cut-off frequency: 50HZ—63HZ—80HZ—100HZ

—125HZ

Output level: –24 to +6

SLA (source level adjustment)

SLA (Source level adjustment) lets you adjust the vo-

lume level of each source to prevent radical changes

in volume when switching between sources.

! Settings are based on the FM volume level, which

remains unchanged.

! The MW/LW volume level can also be adjusted

with this function.

! When selecting FM as the source, you cannot

switch to SLA.

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the source volume.

Adjustment range: +4 to –4

3 Press M.C. to confirm the selection.

Autogood products «130»

Section