Pioneer DEH-5000UB Panduan Instalasi - Halaman 5
Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Penerima Mobil Pioneer DEH-5000UB. Pioneer DEH-5000UB 8 halaman.
Halaman Cetak10. Note
1. USB input (DEH-5000UB)
Connect to sparately sold
Depending on the kind of vehicle,
USB device.
the function of 3* and 5* may be
20 cm
different. In this case, be sure to
connect 2* to 5* and 4* to 3*.
8. This product
1*
2. Rear output or
3*
2*
subwoofer output
3. Antenna jack
5*
4*
4. Fuse (10 A)
11. Connect leads of the
same color to each other.
12. Cap (1*)
Do not remove cap
if this terminal is
not in use.
13. Yellow (3*)
14. Yellow (2*)
Back-up (or
Connect to the constant
accessory)
12 V supply terminal.
15. Red (5*)
16. Red (4*)
Accessory
Connect to terminal controlled by
(or back-up)
ignition switch (12 V DC).
17. Black (chassis ground)
Connect to a clean, paint-free metal location.
18. ISO connector
Note
19. Yellow/black
In some vehicles, the ISO connector
If you use an equipment with Mute
may be divided into two. In this case,
function, wire this lead to the Audio
be sure to connect to both connectors.
Mute lead on that equipment. If not,
keep the Audio Mute lead free of any
connections.
7. AUX jack (3.5 φ)
Use a stereo mini plug cable
to connect with auxiliary device.
6. Wired remote input
Hard-wired remote control
24.To Rear output or
adaptor can be connected
subwoofer output
(sold separately).
25. Connect with RCA cables
5. USB input (DEH-50UB)
(sold separately)
2 m
9. USB cable (DEH-50UB)
Connect to sparately sold
USB device.
27. System remote control
20. Blue/white
Connect to system control terminal of the
28. Left
power amp (max. 300 mA 12 V DC).
30.Rear speaker
21. Blue/white (7*)
or subwoofer
Connect to auto-antenna relay control
terminal (max. 300 mA 12 V DC).
31. Perform these connections when
22. Blue/white (6*)
using the optional amplifier.
The pin position of the ISO connector will
32. Notes
differ depends on the type of vehicle.
Connect 6* and 7* when Pin 5 is an
• Change the initial setting of this unit (refer to the
antenna control type. In another type of
operation manual). The subwoofer output of this unit is
vehicle, never connect 6* and 7*.
monaural.
• When using a subwoofer of 70 W (2 Ω), be sure to
connect with Violet and Violet/black leads of this unit.
23. Speaker leads
Do not connect anything with Green and Green/black
White:
Front left
leads.
White/black: Front left
Gray:
Front right
Gray/black: Front right
Green:
Rear left
or subwoofer
Green/black: Rear left
or subwoofer
Violet:
Rear right
or subwoofer
Violet/black: Rear right
or subwoofer
Connecting the units
Note
• When this unit is installed in a vehicle without
ACC (accessory) position on the ignition switch,
red cable must be wired to the terminal that can
detect the operation of the ignition key. Otherwise,
battery drain may result.
26. Power amp
(sold separately)
ACC position
No ACC position
• Use this unit in other than the following
conditions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
• To prevent short-circuit, overheating or
malfunction, be sure to follow the directions
below.
— Disconnect the negative terminal of the
29. Right
battery before installation.
— Secure the wiring with cable clamps or
adhesive tape. To protect the wiring, wrap
adhesive tape around them where they lie
30.Rear speaker
against metal parts.
or subwoofer
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors with
insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker's
negative cables.
English
Connecting the units
Connection Diagram
• Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
1. USB input (DEH-5000UB)
external power amp's system remote control or
Connect to separately sold USB device.
the vehicle's auto-antenna relay control terminal
2. Rear output or subwoofer output
(max. 300 mA, 12 V DC). If the vehicle is equipped
with a glass antenna, connect it to the antenna
3. Antenna jack
booster power supply terminal.
4. Fuse (10 A)
• Never connect blue/white cable to external power
5. USB input (DEH-50UB)
amp's power terminal. Also, never connect
6. Wired remote input
it to the power terminal of the auto antenna.
Hard-wired remote control adaptor can be
Otherwise, battery drain or malfunction may
connected (sold separately).
result.
7. AUX jack (3.5 ø)
• Black cable is ground. This cable and other
product's ground cable (especially, high-current
Use a stereo mini plug cable to connect with
products such as power amp) must be wired
auxiliary device.
separately. Otherwise, fire or malfunction may
8. This product
result if they are accidentally detached.
9. USB cable (DEH-50UB)
Connect to separately sold USB device.
10. Note
Depending on the kind of vehicle, the function
of 3* and 5* may be different. In this case, be
sure to connect 2* to 5* and 4* to 3*.
11. Connect leads of the same color to
each other.
12. Cap (1*)
Do not remove cap if this terminal is not in use.
13. Yellow (3*)
Back-up (or accessory)
14. Yellow (2*)
Connect to the constant 12 V supply terminal.
15. Red (5*)
Accessory (or back-up)
16. Red (4*)
Connect to terminal controlled by ignition
switch (12 V DC).
17. Black (chassis ground)
Connect to a clean, paint-free metal location.
18. ISO connector
Note
In some vehicles, the ISO connector may
be divided into two. In this case, be sure to
connect to both connectors.
19. Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
20. Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
English
21. Blue/white (7*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
22. Blue/white (6*)
The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6*
and 7* when Pin 5 is an antenna control type.
In another type of vehicle, never connect 6*
and 7*.
23. Speaker leads
White: Front left
White/black: Front left
Gray: Front right
Gray/black: Front right
Green: Rear left or subwoofer
Green/black: Rear left or subwoofer
Violet: Rear right or subwoofer
Violet/black: Rear right or subwoofer
24. To rear output or subwoofer output
25. Connect with RCA cables (sold separately)
26. Power amp (sold separately)
27. System remote control
28. Left
29. Right
30. Rear speaker or subwoofer
31. Perform these connections when using the
optional amplifier.
32. Notes
• Change the initial setting of this unit (refer
to the operation manual). The subwoofer
output of this unit is monaural.
• When using a subwoofer of 70 W (2 Ω), be
sure to connect with Violet and Violet/black
leads of this unit. Do not connect anything
with Green and Green/black leads.