Pioneer DEH-7350BT Panduan Pemilik - Halaman 11

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Penerima Mobil Pioneer DEH-7350BT. Pioneer DEH-7350BT 21 halaman. Cd rds receiver

Halaman Cetak

Installation

! To prevent a short-circuit, overheating or mal-

Connections

WARNING

! Use speakers over 50 W (output value) and

between 4 W to 8 W (impedance value). Do

not use 1 W to 3 W speakers for this unit.

! The black cable is ground. When installing

this unit or power amp (sold separately),

make sure to connect the ground wire first.

Ensure that the ground wire is properly con-

nected to metal parts of the car's body. The

ground wire of the power amp and the one of

this unit or any other device must be con-

nected to the car separately with different

screws. If the screw for the ground wire loos-

ens or falls out, it could result in fire, genera-

tion of smoke or malfunction.

Ground wire

POWER AMP

Other devices

Metal parts of car's body

(Another electronic

device in the car)

! When this unit is on, control signals are sent

Important

! When installing this unit in a vehicle without

an ACC (accessory) position on the ignition

switch, failure to connect the red cable to the

terminal that detects operation of the ignition

key may result in battery drain.

! Never connect the blue/white cable to the

ACC position

No ACC position

! Use this unit with a 12-volt battery and nega-

tive grounding only. Failure to do so may re-

sult in a fire or malfunction.

This unit

function, be sure to follow the directions

below.

— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. Wrap adhesive tape around wiring

that comes into contact with metal parts to

protect the wiring.

— Place all cables away from moving parts,

such as the gear shift and seat rails.

1 Power cord input

— Place all cables away from hot places, such

2 Microphone input

as near the heater outlet.

3 Microphone

— Do not connect the yellow cable to the battery

4 Rear output or subwoofer output

by passing it through the hole to the engine

5 Front output

compartment.

6 Antenna input

— Cover any disconnected cable connectors

7 Fuse (10 A)

with insulating tape.

8 Wired remote input

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power with

other devices. The current capacity of the

Power cord

cable is limited.

Perform these connections when not connect-

— Use a fuse of the rating prescribed.

ing a rear speaker lead to a subwoofer.

— Never wire the negative speaker cable directly

to ground.

— Never band together negative cables of multi-

ple speakers.

through the blue/white cable. Connect this

cable to the system remote control of an ex-

ternal power amp or the vehicle's auto-anten-

na relay control terminal (max. 300 mA 12 V

DC). If the vehicle is equipped with a glass

antenna, connect it to the antenna booster

power supply terminal.

power terminal of an external power amp.

Also, never connect it to the power terminal

of the auto antenna. Doing so may result in

battery drain or a malfunction.

Installation

Perform these connections when using a sub-

woofer without the optional amplifier.

4 5

1 To power cord input

2 Left

Hard-wired remote control adaptor can be

3 Right

connected (sold separately).

4 Front speaker

5 Rear speaker

6 White

7 White/black

8 Gray

9 Gray/black

a Green

b Green/black



c Violet



d Violet/black



e Black (chassis ground)



f Yellow



g Red

h Blue/white

i Subwoofer (4 Ω)

Section













Connect to a clean, paint-free metal location.

Connect to the constant 12 V supply termi-

nal.

Connect to terminal controlled by ignition

switch (12 V DC).

Connect to system control terminal of the

power amp or auto-antenna relay control ter-

minal (max. 300 mA 12 V DC).

<YRD5325-A/N>11