Pioneer SPH-10BT Panduan Instalasi - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Penerima Mobil Pioneer SPH-10BT. Pioneer SPH-10BT 33 halaman. Smartphone receiver
Juga untuk Pioneer SPH-10BT: Petunjuk Pembaruan Firmware (4 halaman), Panduan Pengoperasian (35 halaman), Petunjuk Pembaruan Firmware (6 halaman), Petunjuk Pembaruan Firmware Sistem (7 halaman)

Halaman Cetak

vehicle. Connect

and

when Pin 5

is an antenna control type. In another

type of vehicle, never connect

and

Blue/white

Connect to the system control terminal

of the power amp (max. 300 mA 12 V

DC).

Blue/white

Connect to the auto-antenna relay

control terminal (max. 300 mA 12 V DC).

Violet/white

Of the two lead wires connected to the

back lamp, connect the one in which

the voltage changes when the gear shift

is in the REVERSE (R) position. This

connection enables the unit to sense

whether the car is moving forwards or

backwards.

Speaker leads

White: Front left

White/black: Front left

Gray: Front right

Gray/black: Front right

Green: Rear left

Green/black: Rear left

Violet: Rear right

Violet/black: Rear right

Orange/white

Connect to a car's illumination signal.

ISO connector

In some vehicles, the ISO connector

may be divided into two. In this case, be

sure to connect to both connectors.

Light green

Used to detect the On/Off status of the

parking brake. This lead must be

connected to the power supply side of

the parking brake switch.

NOTES

• Change the initial menu of this unit. Refer

to [REAR-SP] in the INITIAL settings. The

subwoofer output of this unit is

monaural.

• When using a subwoofer of 2 Ω, be sure

to connect the subwoofer to the violet

and violet/black leads of this unit. Do not

connect anything to the green and

green/black leads.

Power amp (sold separately)

Perform these connections when using the

optional amplifier.

System remote control

Connect to blue/white cable.

Power amp (sold separately)

Connect with RCA cables (sold

separately)

To front output

Front speaker

To rear output or subwoofer output

Rear speaker or subwoofer

Installation

Important

• Check all connections and systems before

final installation.

• Do not use unauthorized parts as this

may cause malfunctions.

• Consult your dealer if installation requires

drilling of holes or other modifications to

the vehicle.

• Do not install this unit where:

– it may interfere with operation of the

vehicle.

– it may cause injury to a passenger as a

result of a sudden stop.

• Install this unit away from hot places such

as near the heater outlet.

• Optimum performance is

obtained when the unit is

installed at an angle of less

than 45°.

• When installing, to ensure proper heat

dispersal when using this unit, make sure

you leave ample space behind the rear

panel and wrap any loose cables so they

are not blocking the vents.

Leave ample

5 cm

space

5 cm

DIN mount installation

Insert the supplied mounting sleeve

into the dashboard.

Secure the mounting sleeve by using a

screwdriver to bend the metal tabs

(90°) into place.

Dashboard

Mounting sleeve

• Make sure that the unit is installed

securely in place. An unstable

installation may cause skipping or

other malfunctions.

When not using the supplied

mounting sleeve

Determine the appropriate position

where the holes on the bracket and

the side of the unit match.

Tighten two screws on each side.

Tapping screw (5 mm × 9 mm, not

supplied with product)

Mounting bracket

Dashboard or console

Removing the unit (installed with

the supplied mounting sleeve)

Remove the trim ring.

Trim ring

• Releasing the front panel allows easier

access to the trim ring.

• When reattaching the trim ring, point

the side with the dent part up.

Insert the supplied extraction keys

into both sides of the unit until they

click into place.

Pull the unit out of the dashboard.