Pioneer Super Tuner IIID DEH-P580MP Panduan Instalasi - Halaman 2
Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Penerima Mobil Pioneer Super Tuner IIID DEH-P580MP. Pioneer Super Tuner IIID DEH-P580MP 6 halaman. Owner's manual
Juga untuk Pioneer Super Tuner IIID DEH-P580MP: Panduan Pemilik (34 halaman)
Halaman Cetak
Connecting the Units
7 When using a Subwoofer without using the optional amplifier
IP-BUS input
(Blue)
This product
Front output
Subwoofer output
Antenna jack
Fuse (10 A)
Yellow/black
If you use an equipment with Mute function, wire this lead to
the Audio Mute lead on that equipment. If not, keep the Audio
Mute lead free of any connections.
Yellow
To terminal always supplied with power regardless of
ignition switch position.
Red
To electric terminal controlled by ignition switch (12
V DC) ON/OFF.
Orange/white
To lighting switch terminal.
Black (ground)
To vehicle (metal) body.
Rear output
15 cm (5-7/8 in.)
Jack for the Wired Remote Control Adaptors
Please see the Instruction Manual for the
Wired Remote Control Adaptors (sold separately).
Multi-CD player
IP-BUS cable
(sold separately)
Blue/white
To system control terminal of the power amp or
Auto-antenna relay control terminal (max. 300
mA 12 V DC).
White
Gray
+
+
Front speaker
≠
≠
White/black
Gray/black
Left
Green
Violet
+
+
Subwoofer
≠
≠
Green/black
Violet/black
Note:
Change the initial setting of this unit (refer to the Operation
Manual). The subwoofer output of this unit is monaural.
<ENGLISH>
Installation
Note:
• Before making a final installation of the unit, tem-
porarily connect the wiring to confirm that the con-
nections are correct and the system works
properly.
• Use only the parts included with the unit to ensure
proper installation. The use of unauthorized parts
can cause malfunctions.
• Consult with your nearest dealer if installation
requires the drilling of holes or other modifications
of the vehicle.
• Install the unit where it does not get in the driver's
way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
• The semiconductor laser will be damaged if it
overheats, so don't install the unit anywhere hot
— for instance, near a heater outlet.
DIN Front/Rear-mount
This unit can be properly installed either from "Front" (conventional DIN Front-mount) or
"Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit
chassis). For details, refer to the following illustrated installation methods.
DIN Front-mount
Installation with the rubber bush (Fig. 5)
Dashboard
182
Front speaker
Right
53
Subwoofer
Fig. 3
Removing the unit (Fig. 6) (Fig. 7)
• If installation angle exceeds 60° from horizontal,
the unit might not give its optimum performance.
(Fig. 4)
60°
Fig. 4
Holder
After inserting the holder into the
dashboard, then select the appropriate
tabs according to the thickness of the
dashboard material and bend them.
(Install as firmly as possible using the
top and bottom tabs. To secure, bend
the tabs 90 degrees.)
Rubber bush
Screw
Fig. 5
<ENGLISH>
Frame
To remove the frame, extend top and
bottom of the frame outwards in
order to unlock it. (When reattaching
the frame, point the side with a
groove downwards and attach it.)
• It becomes easy to remove the
frame if the front panel is released.
Fig. 6
Insert the supplied extraction keys
into the unit, as shown in the figure,
until they click into place. Keeping
the keys pressed against the sides of
the unit, pull the unit out.
Fig. 7