Pioneer AVH-W4400NEX Panduan Instalasi - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Penerima Pioneer AVH-W4400NEX. Pioneer AVH-W4400NEX 33 halaman. Dvd rds av receiver

Halaman Cetak

(impedance value). Do not use 1 Ω to 3 Ω

speakers for this product.

• The black lead is ground. When installing

this unit or power amp (sold separately),

make sure to connect the ground wire

first. Ensure that the ground wire is

properly connected to metal parts of the

car's body. The ground wire of the power

amp and the one of this unit or any other

device must be connected to the car

separately with different screws. If the

screw for the ground wire loosens or falls

out, it could result in fire generation of

smoke or malfunction.

Ground wire

POWER AMP

Other devices

Metal parts of car's

(Another electronic

body

device in the car)

*1 Not supplied for this unit

• When replacing the fuse, be sure to only

use a fuse of the rating prescribed on this

product.

• When disconnecting a connector, pull the

connector itself. Do not pull the lead, as

you may pull it out of the connector.

• This product cannot be installed in a

vehicle without ACC (accessory) position

on the ignition switch.

ACC position

No ACC position

• To avoid short-circuiting, cover the

disconnected lead with insulating tape. It

is especially important to insulate all

unused speaker leads, which if left

uncovered may cause a short circuit.

• For connecting a power amp or other

devices to this product, refer to the

manual for the product to be connected.

• The graphical symbol

placed on

the product means direct current.

Notice for the blue/

white lead

• When the ignition switch is turned on

(ACC ON), a control signal is output

through the blue/white lead. Connect to

an external power amp's system remote

control terminal, the auto-antenna relay

control terminal, or the antenna booster

power control terminal (max. 300 mA 12

V DC). The control signal is output

through the blue/white lead, even if the

audio source is switched off.

Important

When this product is in [Power OFF] mode,

the control signal is also turned off. If

[Power OFF] mode is canceled, the control

signal is output again and the antenna is

extended with the auto antenna function

(if the antenna is being used). Be careful so

that the extended antenna does not come

into contact with any obstacles.

Rear panel (main

terminals)

GPS antenna 3.55 m (11 ft. 8 in.)

Microphone 3 m (9 ft. 10-1/8 in.)

iDatalink adapter input

Refer to the instruction manual for the

iDataLink adapter (sold separately).

RGB cable (supplied with Navigation

system)

SiriusXM Connect Vehicle Tuner

Refer to the instruction manual for

SiriusXM Connect Vehicle Tuner (sold

separately).

This product

Pioneer navigation system

Contact your dealer to inquire about

the connectable navigation unit.

Antenna jack

AV cable IN/OUT

Power supply

Fuse (10 A)

Wired remote input

Hard-wired remote control adapter can

be connected (sold separately).

NOTE

Before using and/or connecting the

iDatalink Maestro adapter, you will need to

first flash the Maestro module with the

appropriate vehicle and head unit

firmware. You can find the device number

that is required for the activation on the

followings (refer to the Operation Manual.):

• The label on the packaging of this

product

• The label on this product

• The [Firmware Information] screen

Power cord

WARNING

IMPROPER CONNECTION MAY RESULT IN

SERIOUS DAMAGE OR INJURY

INCLUDING ELECTRICAL SHOCK, AND

INTERFERENCE WITH THE OPERATION

OF THE VEHICLE'S ANTILOCK BRAKING

SYSTEM, AUTOMATIC TRANSMISSION

AND SPEEDOMETER INDICATION.

To power supply

Power cord

Yellow

To terminal supplied with power

regardless of ignition switch position.

Red

To electric terminal controlled by

ignition switch (12 V DC) ON/OFF

Orange/white