Pioneer DEH-S1290UB Panduan Pemilik - Halaman 10
Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Penerima Pioneer DEH-S1290UB. Pioneer DEH-S1290UB 16 halaman. Cd rds receiver
Halaman Cetak
*1 Depending on your car, this function may not work properly. In this case, contact your dealer or an
authorized PIONEER Service Station.
*2 Please use a commercially available wiring harness for each car model when [PRESET] mode is
engaged, and use a commercially available adapter when in [PIONEER].
ILLUMINATION settings
Menu Item
DIM SETTING
[SYNC CLOCK], [MANUAL]
BRIGHTNESS
[1] to [10]
MIXTRAX settings
Menu Item
SHORT PLAYBCK
[1.0 MIN], [1.5 MIN], [2.0 MIN],
[2.5 MIN], [3.0 MIN], [OFF]
MIX PATTERN
[SOUND LEVEL]
[LOW PASS]
[RANDOM]
DISPLAY FX
[ON], [OFF]
CUT IN FX
[ON], [OFF]
10
En
Description
Select the way to change the display brightness.
Change the display brightness.
The available setting ranges differ depending on
[DIM SETTING].
Description
Select the length of the playback time.
Change the MIXTRAX special effects according
to the audio level.
The mix pattern changes according to the
sound level.
The mix pattern changes according to the bass
level.
The mix pattern changes randomly according
to the sound level mode and low pass mode.
Set the MIXTRAX special effects on/off.
Turn the MIXTRAX sound effects on/off while
manually changing the tracks.
Connections/Installation
Connections
WARNING
• When speaker output is used by 4
channels, use speakers over 50 W
(maximum input power) and between 4
Ω to 8 Ω (impedance value). Do not use 1
Ω to 3 Ω speakers for this unit.
• When rear speaker output is used by 2 Ω
of subwoofer, use speakers over 70 W
(maximum input power).
* Please refer to connections for a
connection method.
• The black cable is ground. When
installing this unit or power amp (sold
separately), make sure to connect the
ground wire first. Ensure that the ground
wire is properly connected to metal parts
of the car's body. The ground wire of the
power amp and the one of this unit or
any other device must be connected to
the car separately with different screws. If
the screw for the ground wire loosens or
falls out, it could result in fire, generation
of smoke or malfunction.
Ground wire
POWER AMP
Other devices
Metal parts of
(Another electronic
car's body
device in the car)
*1 Not supplied for this unit
Important
• When installing this unit in a vehicle
without an ACC (accessory) position on
the ignition switch, failure to connect the
red cable to the terminal that detects
operation of the ignition key may result
in battery drain.
ACC position
No ACC position
• Use this unit with a 12-volt battery and
negative grounding only. Failure to do so
may result in a fire or malfunction.
• To prevent a short-circuit, overheating or
malfunction, be sure to follow the
directions below.
– Disconnect the negative terminal of the
battery before installation.
– Secure the wiring with cable clamps or
adhesive tape. Wrap adhesive tape
around wiring that comes into contact
with metal parts to protect the wiring.
– Place all cables away from moving parts,
such as the shift lever and seat rails.
– Place all cables away from hot places,
such as near the heater outlet.
– Do not connect the yellow cable to the
battery by passing it through the hole
to the engine compartment.
– Cover any disconnected cable
connectors with insulating tape.
– Do not shorten any cables.
– Never cut the insulation of the power
cable of this unit in order to share the
power with other devices. The current
capacity of the cable is limited.
– Use a fuse of the rating prescribed.
– Never wire the negative speaker cable
directly to ground.
– Never band together negative cables of
multiple speakers.
• When this unit is on, control signals are
sent through the blue/white cable.
Connect this cable to the system remote