Pioneer DVH-340UB Panduan Instalasi - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Penerima Pioneer DVH-340UB. Pioneer DVH-340UB 41 halaman. Dvd rds receiver
Juga untuk Pioneer DVH-340UB: Panduan Memulai Cepat (17 halaman), Panduan Pengoperasian (45 halaman)

Halaman Cetak

Section

Connections

WARNING

! To avoid the risk of accident and the potential

violation of applicable laws, no viewing of

front seat video should ever occur while the

vehicle is being driven. Also, rear displays

should not be in a location where they are

visibly distracting to the driver.

! In some countries or states the viewing of im-

ages on a display inside a vehicle even by

persons other than the driver may be illegal.

Where such regulations apply, they must be

obeyed and this unit's DVD features should

not be used.

CAUTION

! PIONEER does not recommend that you in-

stall or service your display unit yourself. In-

stalling or servicing the product may expose

you to risk of electric shock or other hazards.

Refer all installation and servicing of your

display unit to authorized Pioneer service

personnel.

! Secure all wiring with cable clamps or elec-

trical tape. Do not allow any bare wiring to re-

main exposed.

! Do not drill a hole into the engine compart-

ment to connect the yellow cable of the dis-

play unit to the vehicle battery. Engine

vibration may eventually cause the insulation

to fail at the point where the wire passes

from the passenger compartment into the

engine compartment. Take extra care in se-

curing the wire at this point.

! It is extremely dangerous to allow the display

lead to become wound around the steering

column or shift lever. Be sure to install the

display in such a way that it will not obstruct

driving.

! Make sure that wires will not interfere with

moving parts of the vehicle, such as the shift

lever, parking brake or seat sliding mecha-

nism.

! Do not shorten any cables. If you do, the pro-

tection circuit may fail to work properly.

Important

! When installing this unit in a vehicle without

an ACC (accessory) position on the ignition

switch, failure to connect the red cable to the

terminal that detects operation of the ignition

key may result in battery drain.

ACC position

No ACC position

! Use of this unit in conditions other than the

following could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 W to

8 W (impedance value).

! To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions

below.

— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. Wrap adhesive tape around wiring

that comes into contact with metal parts to

protect the wiring.

— Place all cables away from moving parts,

such as the shift lever and seat rails.

— Place all cables away from hot places, such

as near the heater outlet.

— Do not connect the yellow cable to the battery

by passing it through the hole to the engine

compartment.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.

Connections

— Never cut the insulation of the power cable of

this unit in order to share the power with

other devices. The current capacity of the

cable is limited.

— Use a fuse of the rating prescribed.

— Never wire the negative speaker cable directly

to ground.

— Never band together negative cables of multi-

ple speakers.

! When this unit is on, control signals are sent

through the blue/white cable. Connect this

cable to the system remote control of an ex-

ternal power amp or the vehicle's auto-anten-

na relay control terminal (max. 300 mA

12 V DC). If the vehicle is equipped with a

glass antenna, connect it to the antenna

booster power supply terminal.

! Never connect the blue/white cable to the

power terminal of an external power amp.

Also, never connect it to the power terminal

of the auto antenna. Doing so may result in

battery drain or a malfunction.

! The black cable is ground. Ground cables for

this unit and other equipment (especially,

high-current products such as power amps)

must be wired separately. If they are not, an

accidental detachment may result in a fire or

malfunction.