Pioneer VSX-532 Panduan Petunjuk Pengoperasian - Halaman 33
Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Penerima Stereo Pioneer VSX-532. Pioneer VSX-532 39 halaman.
Halaman Cetak
7
7
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and
malfunctions. If you think that there is something wrong with
this component, check the points below. Take a look at the
other components and electrical appliances being used,
because sometimes the problem may lie there. If the trouble
isn't sorted out even after going through the checks below,
ask your nearest Pioneer authorized independent service
company to carry out repair work.
•
If the unit does not operate normally due to external effects
such as static electricity disconnect the power plug from
the outlet and insert again to return to normal operating
conditions.
General
The power does not turn on.
#
Disconnect the power plug from the outlet, and insert again.
The receiver suddenly switches off.
#
When the Auto Power Down function is working, the power
will automatically turn off if the receiver has not operated for
several hours. Check the setting for the Auto Power Down
function (see
The Auto Power Down menu on page
#
Make sure there are no loose strands of speaker wire
touching the rear panel. This could cause the receiver to shut
off automatically.
#
After about a minute (you won't be able to switch the unit on
during this time), switch the receiver back on. If the message
persists, call a Pioneer authorized independent service
company.
#
If there is very little low frequency information in the source
material, change your speaker settings to Front: SMALL /
Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS
(page
29).
The HDMI indicator blinks and the power does not turn
on.
#
The receiver may have a serious problem. Do not try
switching the receiver on. Unplug the receiver from the wall
and call a Pioneer authorized independent service company.
The input of this unit switches from one to another.
(When the ARC function is ON)
#
The CEC (Consumer Electronic Control) function may
activate when the ARC function is turned ON, causing the
input to switch from one to another. Since this unit does not
guarantee synchronized operation based on the CEC
function, turn OFF the HDMI CONTROL setting on the
connected player. Refer to the relevant device's instruction
manual for details.
If this does not work, turn OFF the ARC function. If this is the
case, listen to the TV audio after connecting this unit and the
TV with an audio cable.
OVERHEAT shows in the display and the power turns off.
#
The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation.
#
Lower the volume level.
TEMP shows in the display and the volume level drops.
#
The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation.
#
Lower the volume level.
No sound is output when an input function is selected.
VOLUME +/–
#
Use
to turn up the volume.
MUTE
#
Press
on the remote control to turn muting off.
AUDIO SEL
#
Set the
to H (HDMI), C1/O1 (digital) or A
(analog) according to the type of connections made
(page
18).
#
Make sure the component is connected correctly (see
Connecting your equipment on page
#
Check the audio output settings of the source component.
31).
#
Refer to the instruction manual supplied with the source
component.
No image is output when an input function is selected.
#
Make sure the component is connected correctly (see
Connecting your equipment on page
#
Use the same type of video cables for the source component
and TV to connect to this receiver (see
connection on page
11).
#
The video input selected on the TV monitor is incorrect. Refer
to the instruction manual supplied with the TV.
No sound from subwoofer.
#
Make sure the subwoofer is switched on.
#
If the subwoofer has a volume knob, make sure it's turned up.
#
The Dolby Digital or DTS source you are listening to may not
have an LFE channel.
#
Switch the subwoofer setting in
to YES or PLUS.
#
Switch the LFE ATT (LFE Attenuate) on
0 or LFEATT 5.
No sound from surround or center speakers.
#
Connect the speakers properly
#
#
#
#
#
#
8).
#
#
#
8).
#
About video outputs
#
#
#
Speaker Setting on page 29
page 27
to LFEATT
#
(page
9).
33
Refer to
Speaker Setting on page 29
to check the speaker
settings.
Refer to
Channel Level on page 30
to check the speaker
levels.
No sound from a specific speaker.
Make sure the speaker cable is connected correctly. (Ensure
that the connection terminal is correct, that the speaker wire is
firmly inserted, and that no speaker wire is touching the rear
panel.)
The Phase Control feature doesn't seem to have an
audible effect.
If applicable, check that the lowpass filter switch on your
subwoofer is off, or the lowpass cutoff is set to the highest
frequency setting. If there is a PHASE setting on your
subwoofer, set it to 0º (or depending on the subwoofer, the
setting where you think it has the best overall effect on the
sound).
Make sure the speaker distance setting is correct for all
speakers (see
Speaker Distance on page
31).
Considerable noise in radio broadcasts.
Connect the antenna
(page
14) and adjust the position for
best reception.
Route any loose cables away from the antenna terminals and
wires.
Fully extend the FM wire antenna, position for best reception,
and secure to a wall (or connect an outdoor FM antenna).
Connect an additional internal or external AM antenna
(page
14).
Turn off equipment causing interference or move it away from
the receiver (or move antennas farther away from equipment
causing noise).
Broadcast stations cannot be selected automatically.
Connect an outdoor antenna
(page
14).
Noise during playback of a cassette deck.
Move the cassette deck away from your receiver, until the
noise disappears.
No sound is output or a noise is output when software
with DTS is played back.
Make sure the player's settings are correct and/or the DTS
signal out is on. Refer to the instruction manual supplied with
the DVD player.
There seems to be a time lag between the speakers and
the output of the subwoofer.
See
Automatically setting up for surround sound (MCACC) on
page 16
to set up your system again using Full Auto MCACC
2
4
33