Pioneer VSX-821-K Panduan Petunjuk Pengoperasian - Halaman 20

Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Penerima Stereo Pioneer VSX-821-K. Pioneer VSX-821-K 20 halaman. Audio/video multi-channel receiver
Juga untuk Pioneer VSX-821-K: Spesifikasi (2 halaman), Panduan Servis (9 halaman)

Halaman Cetak

Pioneer VSX-821-K Panduan Petunjuk Pengoperasian

Basic Setup

Chapter 3:

Basic Setup

Before setting up

This receiver allows you to adjust the system setup, and operate

iPod/USB devices for playback, using the on-screen display (OSD)

that is shown on the TV screen.

• The OSD will not appear if you have connected using the HDMI

output to your TV. Use composite or component connections

for system setup.

First, follow the procedure below to make sure that the OSD screen

is displayed.

Switch on the receiver and your TV.

Switch the TV input to the input that connects this

receiver to the TV through the corresponding composite or

component cable.

For example, if you connected this receiver to the VIDEO jacks on

your TV, make sure that the VIDEO input is now selected.

Press

on the remote control, then press the

RECEIVER

SETUP button.

The System Setup menu of the OSD screen will be displayed on the

TV. If nothing appears on the screen, try to change the TV format

setting on the receiver (see below).

Changing the TV format setting

If the OSD screen is not displayed correctly, it may be that the TV

system is set incorrectly for your country or region.

Switch the receiver into standby.

While holding down the TUNE  button, press and hold

the  STANDBY/ON button for about two seconds.

The display shows the new setting (PAL or NTSC).

Canceling the demo display

The display on the front panel shows various information (demo

displays) when the receiver is not operating.

You can turn off the demo display. For details, see The FL Demo

Mode menu on page 36.

• The demo mode is canceled automatically when the Auto

MCACC setup is performed (see below).

Automatically setting up for surround sound

(MCACC)

The Auto Multi-Channel Acoustic Calibration (MCACC) setup

measures the acoustic characteristics of your listening area,

taking into account ambient noise, speaker size and distance, and

tests for both channel delay and channel level. After you have set

up the microphone provided with your system, the receiver uses

the information from a series of test tones to optimize the speaker

settings and equalization for your particular room.

CAUTION

• The test tones used in the Auto MCACC setup are output at

high volume.

Important

• The OSD will not appear if you have connected using the HDMI

output to your TV. Use composite or component connections

for system setup.

• The Auto MCACC setup will overwrite any existing speaker

settings you've made.

• Before using the Auto MCACC setup, the iPod USB input

should not be selected as an input source.

• If you connected either the surround back speaker or the front

height speaker, make sure that the Pre Out setting is correctly

set before performing the Auto MCACC setup (see page 35).

(Here is an explanation using the OSD screen for a surround

back speaker connection.)

PARAMETER

TOP

RECEIVER

SLEEP

SOURCE

CONTROL

RECEIVER

INPUT SELECT

INPUT

HOME

DVD

SETUP

iPod CTRL

PTY SEARCH

Switch on the receiver and your TV.

Switch the TV input to the input that connects this

receiver to the TV through the corresponding composite or

component cable.

Connect the microphone to the MCACC SETUP MIC jack

on the front panel.

Make sure there are no obstacles between the speakers and the

microphone.

PHONES

If you have a tripod, use it to place the microphone so that it's

about ear level at your normal listening position. Otherwise, place

the microphone at ear level using a table or a chair.

Press

RECEIVER

SETUP button.

The System Setup menu appears on your TV. Use /// and

ENTER on the remote control to navigate through the screens and

select menu items. Press RETURN to exit the current menu.

• Press SETUP at any time to exit the System Setup menu. If you

cancel the Auto MCACC setup at any time, the receiver

TOOLS

VOLUME

automatically exits and no settings will be made.

• The screensaver automatically starts after three minutes of

inactivity.

ENTER

Select 'Auto MCACC' from the System Setup menu, then

press ENTER.

BAND

RETURN

DTV/ TV

MUTE

• MIC IN blinks when the microphone is not connected to

MCACC SETUP MIC jack.

CONTROL

ON / OFF

VIDEO 2 INPUT

2.1 A

iPod

iPhone

USB

MCACC

SETUP MIC

AUDIO R

VIDEO

iPad

Microphone

Tripod

on the remote control, then press the

System Setup

1.Auto MCACC

2.Manual SP Setup

3.Input Assign

4.Pre Out Setting

5.HDMI Setup

6.Auto Power Down

7.FL Demo Mode

Return