Pioneer A-20-K/-S Panduan Petunjuk Pengoperasian - Halaman 10
Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Penguat Pioneer A-20-K/-S. Pioneer A-20-K/-S 13 halaman.
Halaman Cetak
04
Operation
Chapter 4:
Operation
Playback
SACD/CD player
Network audio player
/I STANDBY/ON
STANDBY
PURE AUDIO
Hi-Bit 32
iPod/USB
5V
2.1A
2
Playback
1
Turn on the power of the playback
component.
2
Turn power ON to the unit.
• If the unit is in the standby mode, press the remote
control's STANDBY/ON button.
3
Select the source you want to playback.
SACD/CD NETWORK
PHONO
TUNER
AUX
RECORDER
Select the playback component.
• When using the A-30's remote control, the INPUT
+/– button can be used to select the component.
• When using the front panel controls, rotate the
INPUT SELECTOR knob.
10
En
iPod dock, etc
Turntable
iPod
Music>
Extras>
Settings>
Shuffle Songs
Backlight
Tuner
MENU
NETWORK AUDIO PLAYER
N-50
FUNCTION
6
6
6
5
3
4
Start playback of the component you
selected in step 1.
5
Adjust playback volume with VOLUME
control.
VOLUME
6
Adjust the tone to your preference using
the BASS and TREBLE controls, and
LOUDNESS button.
If the DIRECT button has been set to ON, these controls
are disabled.
Set the power to Standby
1
Press the remote control's STANDBY/
ON button.
The next time you wish to turn on the power, press the
remote control's STANDBY/ON button.
CD recorder or
• In the case of the A-30/A-20, If the front panel's
tape deck
STANDBY/ON button is pressed, the power will
be turned off. In this case, if the power is off,
pressing the remote control's STANDBY/ON
button will not turn on the power. To turn on the
power again, press the front panel's STANDBY/
ON button.
Note
• If the power cord is disconnected when the unit is
in the standby mode the unit will turn off, but when
the cord is then reconnected, the unit will not
automatically turn on. After reconnecting the
power cord, press the remote control's
Playback
STANDBY/ON button to turn the power on.
When using the unit as a power amplifier
(A-30 only)
When a pre-amplifier is connected to the unit's POWER
AMP DIRECT terminals, the unit can be used as a power
amplifier.
1
Press the POWER AMP DIRECT button
on the front panel of the unit.
The POWER AMP DIRECT indicator will light.
Caution
• When the POWER AMP DIRECT indicator is
lighted, operations change as follows:
– The unit's front-panel VOLUME, BASS, TREBLE,
and BALANCE controls are disabled. These
adjustments are controlled by the component
connected to the unit's POWER AMP DIRECT
terminals.
– When the POWER AMP DIRECT indicator is
lighted, sound volume from the A-30 will
automatically be fixed at its maximum output.
When using this unit as a power amplifier,
check the output level of the component
connected to the POWER AMP DIRECT
terminals and set it to a low level as appropriate
before turning on the POWER AMP DIRECT
indicator. If the sound volume of the component
connected to the POWER AMP DIRECT
terminals is initially set to a high output level,
loud sound may suddenly be output when the
POWER AMP DIRECT indicator lights.
– Sound is not produced from the PHONES jack
and RECORDER OUT terminals.
• For more information, consult the operating
instructions for the component connected to the A-
30's POWER AMP DIRECT terminals.