Pioneer PRS-X340 Panduan Pemilik - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Penguat Pioneer PRS-X340. Pioneer PRS-X340 8 halaman. Bridgeable four-channel power amplifier
Juga untuk Pioneer PRS-X340: Panduan Servis (31 halaman)

Halaman Cetak

Installation

CAUTION

Example of installation on the floor

• Do not install in:

mat or on the chassis

—Places where it could injure the driver or pas-

sengers if the vehicle stops suddenly.

—Places where it may interfere with the driver,

1. Attach the bracket to the main unit.

such as on the floor in front of the driver's

seat.

• Make sure that wires are not caught in the sliding

mechanism of the seats, resulting in a short-cir-

cuit.

• Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier.

Protect all cables and important equipment such

as fuel lines, brake lines and electrical wiring

from damage.

• Install tapping screws in such a way that the

screw tip does not touch any wire. This is impor-

tant to prevent wires from being cut by vibration

of the car, which can result in fire.

2. Place the amplifier where it is to be

• To prevent electric shock, do not install the ampli-

fier in places where it might come in contact with

installed. Insert the supplied tapping

liquids.

× 18 mm) into the screw

screws (4

• To ensure proper installation, use the supplied

holes. Push on the screws with a

parts in the manner specified. If any parts other

than the supplied ones are used, they may damage

screwdriver so they make marks

internal parts of the amplifier, or they may

where the installation holes are to be

become loose causing the amplifier to shut down.

located.

To prevent malfunction

• To ensure proper heat dissipation of the amplifier,

be sure of the following during installation.

—Allow adequate space above the amplifier for

proper ventilation.

—Do not cover the amplifier with a floor mat or

carpet.

• Do not install the amplifier near a door where it

may get wet.

• Do not install the amplifier on unstable places

such as the spare tire board.

• The best location for installation differs with the

car model and installation location. Secure the

amplifier at a sufficiently rigid location.

• Make temporary connections first and check that

the amplifier and the system operate properly.

• After installing the amplifier, confirm that the

spare tire, jack and tools can be easily removed.

3. Drill 2.5 mm diameter holes at the

Fitting the end cap

point marked, and install the ampli-

fier, either on the carpet or directly

1. Align the main unit and end cap

to the chassis.

Tapping-screws

(4 × 18 mm)

Bracket

Screw

Floor mat

or chassis

Drill a 2.5 mm diameter hole

2. Tighten the screw with a 4 mm or

Example of a set up with two units

side by side

You can set up two units with the opposing

holes, and insert the screw.

ends joined together.

Screw

(Refer to the illustration in step 2.)

1. Remove the bracket screw, adjust

Endcap

the bracket to the desired position,

and then tighten the screw once

more to secure.

5/32 inch hexagonal wrench (not

supplied).

Hexagonal wrench

Specifications

2. Setting up with two units joined.

Power source .............................................................................................................. 14.4 V DC (10.8 — 15.1 V allowable)

Grounding system ............................................................................................................................................ Negative type

If you remove the end cap badge screw,

Current consumption ........................................................................................................ 43.7 A (at continuous power, 4 Ω)

you can adjust the badge so that the letters

Average current drawn* ........................................................................................................ 14.5 A (4 Ω for four channels)

are straight.

Fuse .......................................................................................................................................................................... 30 A × 3

Dimensions ........................................................................................................................ 264 (W) × 65 (H) × 345 (D) mm

Weight ...................................................................................................... 7.0 kg (15.4 lbs) (Leads for wiring not included)

Continuous power output ........................................................ 37.5 W × 4 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.04% THD)

Load impedance ............................................................................................................................ 4 Ω (1 — 8 Ω allowable)

Badge

Frequency response ............................................................................................................ 10 — 50,000 Hz (+0 dB, –1 dB)

Signal-to-noise ratio ...................................................................................................................... 105 dB (IHF–A network)

Distortion ............................................................................................................................................ 0.005% (10 W, 1 kHz)

Separation ........................................................................................................................................................ 65 dB (1 kHz)

Variable crossover network

Endcap

Bracket

Maximum input level/impedance .................................................................................... RCA: 6.5 V/22 kΩ (0.4 — 6.5 V)

Screw

Note:

Screw

• Specifications and the design are subject to possible modification without notice

*Average current drawn

• The average current drawn is nearly the maximum current drawn by this unit

26.5 A (4 Ω for two channels)

[10-3/8 (W) × 2-1/2 (H) × 13-5/8 (D) in]

150 W × 2 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.4% THD)

75 W × 4 (at 14.4 V, 2 Ω, 20 — 20,000 Hz, 0.4% THD)

(Bridge connection: 2 — 8 Ω allowable)

A CH: LPF-L/LPF-H/HPF-L/BPF

B CH: LPF-L/LPF-H/HPF-L/HPF-H

Cut off frequency .................................................................................................... Low frequency: 40 — 120 Hz

High frequency: 3k — 9k Hz

Cut off slope .......................................................................................................................................... –12 dB/oct

due to improvements.

when an audio signal is input. Use this value when working out total current

drawn by multiple power amplifiers.