Pioneer SX-201 Panduan Petunjuk Pengoperasian - Halaman 2
Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Penguat Pioneer SX-201. Pioneer SX-201 17 halaman. Stereo control amplifier
Juga untuk Pioneer SX-201: Panduan Petunjuk Pengoperasian (28 halaman)
Halaman Cetak
| IMPORTANT
The hghteung fast: with arrowhead, within an equilateret
tnangle, 1s intended to alert the user to the presence of
uniesisal
s voltage" within the product's
enclasur
t magnitude
to constitute
arisk of al
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
TO PREVENT THE RISK OF ELECTRIC SHOCK. DO
NOY REMOVE
COVER (OR BACK}.
NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO.
QUALIFIED SERVICE PERSONNEL.
READ INSTRUCTIONS — All the safety and operating
instruations should be read before the appliance is
operated.
RETAIN INSTRUCTIONS — The safety and operating
instructions
should
be retained
for future
reference.
HEED WARNING — All warnings on the appliance
andin
the operating instructions should be adhered to.
FOLLOW
INSTRUCTIONS
— All operating and use
instructions should be fallowed
WATER AND MOISTURE — The apptian:
be used near water — for example, nea
washbowl, kitchen sink, laundry t
basement, or near a swimming poo!
LOGATION — The appliance should be instalted in a
stable location.
WALL OR CEILING MOUNTING © The appliance
should not be mounted to a wall or ceiling.
VENTILATION — The appliance should be situated so
that its location or position does not interfere
with
its proper ventilation. For example, the appliance
should
notbe situated on a bed, sofa. rug, or similar
surface that may
biock the ventilation openings: of
placed in a built-in installation, such as a bookcase
or cabinet that may impede the flow of air through
the ventilation openings.
HEAT ~ The appliance should be siated away fro
heat sources such as radiators, heat re
stoves, or other appliances (including amplifiers)
that produce heat.
POWER
SOURCES
—
The
appliance
should
be
connected to a power supply only of the type
described in the operating instructions o: as
marked on the appliance.
POWER-CORD
PROTECTION
—
Power supply cords
should be routed so that they gre not likely to be
walked on or pinched by it
placed upon or
against them. Pay particular attention to cords at
plugs, convenience recepta
and the point
where they exit from the appliance,
POLARIZATION
~
If your
purchased
product
is
provided with a polarized power plug. please read
the following instructions. This productis equipped
with a polarized alternating current line plug (a plug
having one biade wider than the other). This plug
will fit into the power outlet only one way This is a
safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. It the
plug should still fail tofit, contact your electrician to
replace your obsolete outles,
Do not deteat the
safety purpose of the polarized piug
CLEANING — The appliance shouid be cleaned only
with a polishing cloth or 2 soft dry cloth. Never
clean with furniture wax, benzine,
insecticides or
other volatile liquids since they may corr
cabinet,
id not
thtub,
wb, in a wet
tenna should be located
POWER LINES ~ An outdoors
away from power lines.
NONUSE PERIODS ~ The power cord of the appliance
should be unplugged from
t h e
gutlet when left
unused for a long penod of time
OBJECT AND LIQUID ENTRY — Care should be taken
50 that objects do n o t fall and liquids are not spitied
into the enclosure through openings.
DAMAGE REQUIRING SERVICE - The appliance
services by a Pioneer authorized service
qualified service personnel when:
supply cord or the plug has been
have fallen, or liquid has been spilled into
the appliance.
The appliance has been exposed to rain.
The appliance does not appear to operate normally
or exhidits @ marked change in performance.
©
The appliance hes deen dropped or the enciosure
damage
SERVICING — The user should not attempt to service
the appliance beyond that described in the
eperating instructions, All other servicing should
be referred to qualified service personnel
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
The exclamation paint within an equilateral triangle is
intended to alert th
SAFETY INSTRUCTIONS —————
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
{NEC SECTION 810 — 20)
GROUNDING CONDUCTORS
{NEC SECTION 810 — 21)
<——=~
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
FIG. A
CHANNEL STEP SWITCH
(Muiti-voltage model only)
[50 kHz/9 kHz] position:
(NEC ART 250, PART H)
OUTDOOR
ANTENNA
GROUNDING
— if an outside
CART — An appliance and cart combination should ¢
ef to the presence of important
nance (servicing) instructions in
anying the appliance.
antenna is connected to the antenna terminal, be
sure the antenna system is grounded so as to
provide some protection against voltage surges
and built-up static charges.
tn the US.A. section 810 of the National Electrical
Code, ANSI/NFPA 70, provides information with
yrounding of the mast and
upporting structure, grounding of the lead-in wire
a n antenna discharge
unit, size of grounding
tors, location of antenna discharge unit,
connection
to
grounding
electrodes,
and
requirements tor the grounding electrode. See Fig.
A
moved with care. Quick stops, excessive
4, and
uneven surfaces
may cause the appliance and cart
combination to overturn.
NEC
NATIONAL
ELECTRIC
CODE
poe
Set to this position, for areas with an FM reception step of 50
kHz, AM 9 kHz.
The unit has been factory preset to the channel allocation and
deemphasis value for the area in which it is to be sold. If these
values are set incorrectly, the frequency display may stop at the
wrong frequency, or sound may be distorted, resulting in an inabil-
ity to reproduce reception signals at their proper sound quality.
For this reason, be sure to confirm that the values are set correct-
ly before first using the unit.
{100 kHz/10 kHz] position:
Set to this position far areas with an FM reception step of 100
kHz, AM
10 kHz.
NOTE:
2
<ARB1357>
When
unsure
about
the channe/
allocation
and de-emphasis
values for your area, consult your dealer for correct information.
CHANNEL.
STEP
5OkHz
100kHz
QkHz
10kHz
44