Pioneer CDJ-700S Panduan Petunjuk Pengoperasian - Halaman 6

Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Pemutar CD Pioneer CDJ-700S. Pioneer CDJ-700S 16 halaman.

Pioneer CDJ-700S Panduan Petunjuk Pengoperasian
BEFORE OPERATIONS

CONNECTIONS

÷ Before making or changing the connections, switch
off the power switch and disconnect the power cord
from the AC outlet.
AUDIO OUTPUT CONNECTION
Connect the player's AUDIO OUT jack to the LINE IN or
AUX IN jack of a DJ mixer or similar component. Make
sure that the white plugs are connected to the left (L)
jacks and the red plugs to the right (R) jacks.
÷ Do not connect this player to the DJ mixer MIC jacks,
as the sound will be distorted and will not be prop-
erly reproduced.
÷ The illustration shows an example of connections
made when the CDJ-700S is connected to the DJM-
300 or DJM-500.
CONTROL JACK CONNECTIONS
Connect both CONTROL jacks of two players with the
accessory mini-plug cable. By connecting two players,
continuous playback on both players can be carried out
alternately. (Refer to page 12.)
By connecting the optional DJM-500 or DJM-300 DJ
mixer to the CONTROL jack of this unit, the fader start-
ing or back cuing of this unit can be controlled from the
audio mixer. For the connection and operation, read the
operating instructions of the DJM-500 or DJM-300 DJ
mixer.
NOTE:
Fader start and relay play cannot be performed simulta-
neously, since different control cable connections are
required.
Stereo
amplifier
LINE INPUT
L
R
R
L
When using fader
start operation
When using relay
play operation
Mini-plug control
cable (accessory)
CON-
TROL
6
<DRB1215>
En
Audio cable
L
AUDIO
R
OUT
HEAD-
PHONE
L
R
CON-
AUDIO
TROL
OUT
CDJ-700S
POWER CORD CONNECTIONS
After all other connections are made, connect the power
cord to a household wall outlet or to the auxiliary AC
power takeoff on your amplifier.
÷ Make sure plugs are fully inserted into the jacks and
wall outlet.
NOTE:
If you do the following actions when the disc is spinning
in the unit, the unit may malfunction.
1) Set the power switch to off, then on.
2) Disconnect the power cord, then connect again.
To correct, press the EJECT button to stop the disc. You
may then resume player operation.
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power cord
when your hands are wet as this could cause a short
circuit or electric shock. Do not place the unit, a piece of
furniture, etc., on the power cord, or pinch the cord.
Never make a knot in the cord or tie it with other cords.
The power cords should be routed such that they are
not likely to be stepped on. A damaged power cord can
cause a fire or give you an electrical shock. Check the
power cord once in a while. When you find it damaged,
ask your nearest PIONEER authorized service center or
your dealer for a replacement.
L
R
LINE
PHONO
PHONO 2
/LINE 2
DJM-500
LINE
CD1
PHONO1 CD2/LINE
L
L
R
R
CH2
CH1
PLAYER CONTROL
R
L
When using fader
start operation
AUDIO
OUT
CON-
TROL
HEAD-
PHONE
L
R
CON-
AUDIO
TROL
OUT
CDJ-700S
DJM-300
L
L
L
SIGNAL
GND
R
R
R
PHONO
CONTROL
CONTROL
LINE
PHONO 1
CD 1
CD 2
/LINE 1
Audio
cable
Mini-plug control
cable (accessory)
L
R